03-04-2019
I would add:-
- Possible router/firewall issues
- Excessive server load (either CPU meaning it never fully connected or too much network traffic leaving it unable to respond)
- DNS lookup failure, i.e. the DNS used by the server went off and the timeout was too long to allow the connection. The server will try to reverse lookup your connection for logging.
- Client side issue perhaps?
It's all a bit vague so I can only be vague in suggestions.
Robin
This User Gave Thanks to rbatte1 For This Post:
10 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
I appreciate iif anybody can help me with this issue. I set up a Linux FTP server which is authorized user ID from AD. I do some configuration on vsftpd.conf file but it doesn't work out. I copy these configuration, can you help me to check again as when i connect through browser it always give me... (2 Replies)
Discussion started by: cthinh
2 Replies
2. UNIX for Dummies Questions & Answers
Hi!
I have 2 servers. The firts has vsftpd server with this configuration:
# Example config file /etc/vsftpd.conf
#
# The default compiled in settings are fairly paranoid. This sample file
# loosens things up a bit, to make the ftp daemon more usable.
# Please see vsftpd.conf.5 for all... (2 Replies)
Discussion started by: Torquemada
2 Replies
3. UNIX for Dummies Questions & Answers
Hi,
Am running the following commands on our server to generate a key for passwordless SSH, however we are getting 100% blank key files.
E.g. when looking id_dsa.pub or id_dsa they are 100% empty - the files get created, but contain no content and have a file size of 0b.
mkdir ~/.ssh... (3 Replies)
Discussion started by: gjp
3 Replies
4. Shell Programming and Scripting
I am writing perl script to configure Cisco device but Variables inside Net::Telnet::Cisco Module doesn't work and passed to device without resolving.
Please advise.
here is a sample of script:
use Net::Telnet::Cisco;
$device = "10.14.199.1";
($o1, $o2, $o3, $o4) = split(/\./,$device);... (5 Replies)
Discussion started by: ahmed_zaher
5 Replies
5. Shell Programming and Scripting
Hi, I have a question.
I define a function using sed command:
replace()
{
searchterm=$1
replaceterm=$2
sed -e "s/$searchterm/$replaceterm/ig" $3 > $WORK'tempfile.tmp'
mv $WORK'tempfile.tmp' $3
}
Then I call
replace 'test = 0' 'test = 1' $myfileThis code works well in... (1 Reply)
Discussion started by: Dark2Bright
1 Replies
6. Shell Programming and Scripting
Hi, I have a question.
I define a function using sed command:
replace()
{
searchterm=$1
replaceterm=$2
sed -e "s/$searchterm/$replaceterm/ig" $3 > $WORK'tempfile.tmp'
mv $WORK'tempfile.tmp' $3
}
Then I call
replace 'test = 0' 'test = 1' $myfile
This code... (1 Reply)
Discussion started by: Dark2Bright
1 Replies
7. AIX
Recently I decided to intall second daemon of SSH for Winbind users.
I mean I have configuration AIX + Samba + AD and I can login to the server via SSH with AD accounts to 22 port without any problems.
But now I have second installation of OpenSSH and don't understand why I can't do the same... (6 Replies)
Discussion started by: jess_t03
6 Replies
8. Solaris
Hello Experts,
I am performing performance tests on a few mysql select queries.
I use the following command to clear the memory disk caches.
sync && echo 3 | sudo tee /proc/sys/vm/drop_caches
I however see that the above command works on RHEL6 but doesn't work on Solaris 10.
I asked... (4 Replies)
Discussion started by: Anirudh Kumar
4 Replies
9. Shell Programming and Scripting
I am sorry if i post in wrong Form.
i have AIX server in which ssh works for all users but sftp only works for root user .
it is too much important for me to solve this .
Your help will be greatly appreciated. (1 Reply)
Discussion started by: khalid khanAIB
1 Replies
10. UNIX for Advanced & Expert Users
I cant ping to some of my machines, but ping works.
I attach screenshots. Port is open and it is 22.
I can't figure out why i cant access.
https://www.unix.com/attachments/unix-for-advanced-and-expert-users/7492d1541541072-cant-ssh-but-ping-works-sshlisten-jpg... (17 Replies)
Discussion started by: tomislav91
17 Replies
LEARN ABOUT ULTRIX
telnetd
telnetd(8c) telnetd(8c)
Name
telnetd - DARPA TELNET protocol server
Syntax
/etc/telnetd
Description
The server supports the DARPA standard TELNET virtual terminal protocol. The TELNET server is invoked when receives a connection request
on the port indicated in the TELNET service description.
The server operates by allocating a pseudo-terminal device for a client, then creating a login process which has the slave side of the
pseudo-terminal as stdin, stdout, and stderr. The server manipulates the master side of the pseudo terminal, implementing the TELNET pro-
tocol and passing characters between the client and login process.
When a TELNET session is started up, sends a TELNET option to the client side indicating a willingness to do remote echo of characters, to
suppress go ahead, and to receive terminal type information from the remote client. If the remote client is willing, the remote terminal
type is propagated in the environment of the created login process. The pseudo terminal allocated to the client is configured to operate
in cooked mode and with XTABS and CRMOD enabled.
Aside from this initial setup, the only mode changes will carry out are those required for echoing characters at the client side of the
connection.
The server supports binary mode, suppress go ahead, echo, and timing mark. It also allows a remote client to do binary, terminal type, and
suppress go ahead.
Restrictions
Some TELNET commands are only partially implemented.
The TELNET protocol allows the exchange of the number of lines and columns on the user's terminal, but does not make use of them.
The terminal type name received from the remote client is converted to lower case.
The server never sends TELNET go ahead commands.
See Also
telnet(1c), pty(4), tty(4), services(5), inetd(8c)
telnetd(8c)