:confused:
Hi:
I donīt know how to add route gateway and when restart the machine lose this route and put other.
In SCO ver 5.6 Enterprise write:
etc\route delete gateway
route add gateway 199.199.1.1.
so , netstat -rn to see if has change -> all ok
Restart -> !!!... (2 Replies)
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Hi all,
i have a rhel 6.2 with a default gateway.
This server is an Intranet office with no internet access.
DNS are already configured and it's possible to resolve my target.
My goal is to link my application (apache forward) only to http://mytarget.yyy through a new gateway (That does... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT SUSE
aseqnet
aseqnet(1) General Commands Manual aseqnet(1)NAME
aseqnet - ALSA sequencer connectors over network
SYNOPSIS
aseqnet [remotehost]
DESCRIPTION
aseqnet is an ALSA sequencer client which sends and receives event packets over network. Suppose two hosts connected by network, hostA as
a server and hostB as a client. The ALSA sequencer system must be running on both hosts. For creating the server port, run the following
on hostA:
hostA% aseqnet
sequencer opened: 128:0
Then a user client 128 with port 0 was opened on hostA. (The client number may vary.) For creating the (network-)client port, run aseqnet
with the hostname of the server:
hostB% aseqnet hostA
sequencer opened: 132:0
Now all events sent to hostA:128:0 are transferred to hostB:132:0, and vice versa.
The ports created by aseqnet can be connected arbitrary to other sequencer ports via aconnect(1). For example, to connect hostB:132:0 to a
MIDI output device 65:0:
hostB% aconnect 132:0 65:0
Then events to hostA:128:0 will be delivered to hostB:65:0. The following command plays MIDI on hostB.
hostA% pmidi -p 128:0 foo.mid
The multiple clients may exist simultaneously. If hostC is connected as a client to hostA, events from from hostA are sent to all con-
nected network clients, i.e. hostB and hostC. However, only one connection is allowed from a client to a server.
To disconnect network, stop all clients before server by ctrl-C or sending signal to them. The server will automatically quit.
OPTIONS -p port
Specify the TCP port number or TCP service name.
-s addr
Subscribe to the given address for read automatically.
-d addr
Subscribe to the given address for write automatically.
-v Verbose mode.
SEE ALSO aconnect(1), pmidi(1)AUTHOR
Takashi Iwai <tiwai@suse.de>.
January 1, 2000 aseqnet(1)