:confused:
Hi:
I donīt know how to add route gateway and when restart the machine lose this route and put other.
In SCO ver 5.6 Enterprise write:
etc\route delete gateway
route add gateway 199.199.1.1.
so , netstat -rn to see if has change -> all ok
Restart -> !!!... (2 Replies)
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Hi all,
i have a rhel 6.2 with a default gateway.
This server is an Intranet office with no internet access.
DNS are already configured and it's possible to resolve my target.
My goal is to link my application (apache forward) only to http://mytarget.yyy through a new gateway (That does... (0 Replies)
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT DEBIAN
vttest
VTTEST(1) General Commands Manual VTTEST(1)NAME
vttest - test VT100-type terminal
SYNOPSIS
vttest [options] [24x80.132]
DESCRIPTION
Vttest is a program designed to test the functionality of a VT100 terminal (or emulator thereof). It tests both display (escape sequence
handling) and keyboard.
The program is menu-driven and contains full on-line operating instructions.
- To run a given menu-item, you must enter its number.
- Menu items start at zero; this is the "Exit" item in almost all cases.
- You can run all menu-items (for a given level) by entering an asterisk, i.e, `*'.
- You can force a repaint of the menu items by entering "?".
- A few menus can be more than one page. Use "n" and "p" to switch to the next or previous page.
OPTIONS
You can specify the screen geometry in the form [24x80.132], i.e., 24 lines, 80 minimum columns, 132 maximum columns. If your terminal
does not switch between 80 and 132 columns you may specify 24x80.80, for example, to avoid a misleading display.
Other options are:
-f file
specify a file containing a DRCS (soft character definition) string.
-l log test results to vttest.log.
-p use padding, e.g., for a VT100 connected to a high-speed line.
-s add time-delay in selected panning/scrolling options to show details.
-8 use 8-bit controls (this can be changed with a menu option).
AUTHOR
Per Lindberg (mcvax,seismo)!enea!suadb!lindberg sometime 1985.
Modified by Thomas Dickey from June 1996, to support nonstandard screen geometry, VT220-VT520, ISO color and xterm-specific tests.
LOCAL VTTEST(1)