02-18-2019
Are you sure you want to add the network on that host? The ...160 is outside your subnet, so you must route through ...145, the default gateway. Please post the output of arp -a or arp -e of the two nodes on your LAN segment.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
:confused:
Hi:
I donīt know how to add route gateway and when restart the machine lose this route and put other.
In SCO ver 5.6 Enterprise write:
etc\route delete gateway
route add gateway 199.199.1.1.
so , netstat -rn to see if has change -> all ok
Restart -> !!!... (2 Replies)
Discussion started by: AlvaroD
2 Replies
2. AIX
Hello ,
We have 3 rs/6000 server's running aix on our local network, so each time I try to ping one of these servers we get a "network is down" error , I've been instructed to use to route add command which is ...
#route add server.ip router.ip
after this the ping command works fine ,... (6 Replies)
Discussion started by: cubicle^dweller
6 Replies
3. IP Networking
I have two networks connected by cisco routers. My first subnet is 192.168.0.0 and my second is 192.168.1.0.
My SCO unix machine is on the 192.168.1.0 subnet with an IP of 192.168.1.231. It can see the entire .1.0 subnet but nothing on the other network.
My cicso router(gateway) to the other... (6 Replies)
Discussion started by: agoodrich
6 Replies
4. Shell Programming and Scripting
Hello all!
We have two fedora routers one at each site. What we are trying to do worked using freesco but not on fedora, i'm not very good at scripting and need a little guidence. Basicly what we are trying to do is if the primary line dies, the router will change it's routes to go through our... (0 Replies)
Discussion started by: slacker
0 Replies
5. IP Networking
We are unable to bring one of our linux boxes into the network once it was restarted. But once we stop and start the network service. We are able to ping the gateway and get into network. After a minute or two we get the following reponse for the ping command
64 bytes from 124.168.215.40:... (6 Replies)
Discussion started by: chrisanto_2000
6 Replies
6. Solaris
Hi,
I am trying to add route command in Solaris 10 machine in the following fashion:
route add -host 10.8.112.10 180.144.1.250 -interface lo0:1
this command fails with an error "lo0:1: bad value"
I want to add a route to 10.8.112.10 that picks 180.144.1.250 as the gateway via the... (3 Replies)
Discussion started by: sudhir_shet
3 Replies
7. AIX
Just want to know if someone has a clue about what could be happening here:
I have an AIX box with four NICs in Ether channel connected to a Cisco Switch.
When I try to ping the default gateway, sometimes it works, but sometimes it doesn't work unless it has a defined static route.
Thanks... (1 Reply)
Discussion started by: witt
1 Replies
8. UNIX for Advanced & Expert Users
I have setup a Linux machine on my server but for some reason Im unable to reach my default gateway. This is causing me to not communicate with the outside world (unable to connect to CentOS repos)
# ifconfig
enp0s3: flags=4163<UP,BROADCAST,RUNNING,MULTICAST> mtu 1500
inet... (3 Replies)
Discussion started by: Junaid Subhani
3 Replies
9. Red Hat
Hi all,
i have a rhel 6.2 with a default gateway.
This server is an Intranet office with no internet access.
DNS are already configured and it's possible to resolve my target.
My goal is to link my application (apache forward) only to http://mytarget.yyy through a new gateway (That does... (0 Replies)
Discussion started by: kamose
0 Replies
10. UNIX for Beginners Questions & Answers
Dear friends
I use RedHat 6.5, which sets the gateway in the configuration file / etc / sysconfig / network as GATEWAY = 192.168.1.26, and the gateway in the configuration file / etc / sysconfig / network-scripts / ifcfg-eth11 as GATEWAY = 192.168.1.256. The two gateways are different.... (6 Replies)
Discussion started by: tanpeng
6 Replies
LEARN ABOUT PLAN9
iproute
IPROUTE(3) Library Functions Manual IPROUTE(3)
NAME
iproute - Internet route table manager
SYNOPSIS
bind -a #P /net
/net/iproute
/net/ipifc
DESCRIPTION
The iproute device allows the specification of routes for families of IP addresses. It maintains a kernel-resident routing table for IP
addresses used by TCP, IL and UDP. Each route consists of a destination IP address, an IP mask, and an IP gateway address. Every packet
sent by the system is routed according to the route table. An address matches the route table entry when a packet's destination address
matches the table destination address under the mask. When a match is found, the packet is sent to the gateway IP address. If there is no
match, the packet is sent with the original destination address. If there are several matches, the one whose mask has the fewest leading
zeros is chosen. (Because of the definition of IP masks, this mask preserves the largest portion of the address and is therefore the most
specific.) This is forced by storing the routes in decreasing number of ones order and returning the first match. The default gateway has
no ones in the mask and is thus the last matched.
Reading iproute reports the current routes entered in the table. Writing control messages to iproute edits the table. Route entries are
made by writing a string of format
add ipdest mask ipgateway
Entries are deleted by writing a string of format
delete ipdest mask
The whole table can be cleared by writing the string
For example, to install a gateway address to accept all IP packets from a machine:
% echo 'add 0.0.0.0 0.0.0.0 131.107.1.5' > /net/iproute
% cat /net/iproute
0.0.0.0 & 0.0.0.0 -> 131.107.1.5
Reading ipifc reports the current IP interfaces being used, one line per interface, showing the device, the maximum transfer unit, the
local address, the network mask, and the network address.
SOURCE
/sys/src/9/port/deviproute.c
SEE ALSO
ip(3), ipconfig(8)
IPROUTE(3)