02-16-2019
Sounds like it is more of a Hyper-V problem than a Red-Hat issue.
It may well be that Hyper-V didn't support newer technology that
Red-Hat may have implemented at the time.
When running any guest OS through a hypervisor, you should try
the hypervisor forums first. This isn't a Windows 10 forum.
7 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
i'm having 2 problems.
1. the system will always look to boot from the net. i've changed the prom settings so that it boots from the disk, by entering "setenv boot-device disk0:3", but the system still seems to want to boot from the net.
2. i replaced my creator3d with an elitem6 and i did... (6 Replies)
Discussion started by: xyyz
6 Replies
2. UNIX for Advanced & Expert Users
hardware on my first FreeBSD server has crashed. i was planning on
swapping the HD into another machine, booting the generic kernel and then
custom tailoring it to the new machine specs.
however, i'm having a problem.
the new machine is using a promise ultra100 card. i don't have any... (2 Replies)
Discussion started by: xyyz
2 Replies
3. Solaris
I have a client with a V1280 onsite and it is having boot problems. Below is the message it is returning when trying to boot. Is this something that anybody has run into, or that you might be able to shed some light on?
{0} ok boot
/ssm@0,0/pci@18,700000/ide@3/cdrom@0,0:f
SunOS Release 5.9... (3 Replies)
Discussion started by: xcwhitex
3 Replies
4. SCO
Hello those more knowledgeable than I:
I have been trying to get xp and SCO to coexist on the same system. I have tried several different ways to make both work, here's the list:
-install xp, image it, move the partition to the end of drive, verify it boots, image again,
-boot off of SCO... (6 Replies)
Discussion started by: stay0ut
6 Replies
5. Solaris
I have a pentium IV with 512 MB ram and 80 GB HDD.
I first installed windows XP on the first primary partition, then Solaris on the second with 20 GB for the solaris partition, and when rebooted , the grub menu functioned as expected giving me the options to dual boot, so next I wanted to install... (3 Replies)
Discussion started by: saagar
3 Replies
6. Solaris
Hello,
I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message:
Sun Fire V440, No Keyboard
Copyright 2007 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.33, 8192 MB... (14 Replies)
Discussion started by: stoci
14 Replies
7. Solaris
I 'm trying to configure a WAN boot server on Solaris10 x86 for sparc clients ..
when i try to set up the server m getting following error
./setup_install_server -w /var/apache2/htdocs/wanboot10/wpath /var/apache2/htdocs/wanboot10/ipath
ERROR: Cannot make WAN boot Image file on this... (6 Replies)
Discussion started by: fugitive
6 Replies
LEARN ABOUT FREEBSD
hv_kvp
HYPER-V(4) BSD Kernel Interfaces Manual HYPER-V(4)
NAME
hv_kvp -- Hyper-V Key Value Pair Driver
SYNOPSIS
To compile this driver into the kernel, place the following lines in the system kernel configuration file:
device hyperv
DESCRIPTION
The hv_kvp driver provides the ability to store, retrieve, modify and delete key value pairs for FreeBSD guest partitions running on Hyper-V.
Hyper-V allows administrators to store custom metadata in the form of key value pairs inside the FreeBSD guest partition. Administrators can
use Windows Powershell scripts to add, read, modify and delete such key value pairs.
The driver is bare bones and merely forwards requests to its counterpart user mode daemon, hv_kvp_daemon(8). The daemon maintains pools of
key value pairs and does the actual metadata management.
The same driver and daemon combination are also used to set and get IP addresses from a FreeBSD guest.
The set functionality is particularly useful when the FreeBSD guest is assigned a static IP address and is failed over from one Hyper-V host
to another. After failover, Hyper-V uses the set IP functionality to automatically update the FreeBSD guest's IP address to its original
static value.
On the other hand, the get IP functionality is used to update the guest IP address in the Hyper-V management console window.
SEE ALSO
hv_ata_pci_disengage(4), hv_netvsc(4), hv_storvsc(4), hv_utils(4), hv_vmbus(4), hv_kvp_daemon(8)
HISTORY
Support for hv_kvp first appeared in FreeBSD 10.0. The driver was developed through a joint effort between Citrix Incorporated, Microsoft
Corporation and Network Appliance Incorporated.
AUTHORS
FreeBSD support for hv_kvp was first added by Microsoft BSD Integration Services Team <bsdic@microsoft.com>.
BSD
September 10, 2013 BSD