01-18-2019
You don't need to wait for it to finish syncing, no.
The device changing number may have been due to a reboot, i.e. one boot was a device you made, the next reboot was auto-assembled and the device number chosen automatically.
By running mkfs on it again you wiped out whatever was on it before.
8 More Discussions You Might Find Interesting
1. Solaris
Hi,
I set up a RAID 5 configuration and for some reason the volumes won't mount when the system boots. I have to manually mount them from the command line and all is fine.
Here's the vfstab entries:
#device device mount FS fsck mount mount
#to mount ... (2 Replies)
Discussion started by: rpollard001
2 Replies
2. UNIX for Advanced & Expert Users
Hello All,
(RHEL4)
Few weeks ago I had posted a message in this forum about the problem I had when I replaced my two scsi disks and tried rebuild raid1 array.
I somehow managed to up the system with working raid1 array.
But the main problem persisted..
i.e when I reboot the system, mounting... (0 Replies)
Discussion started by: ravinandan
0 Replies
3. UNIX for Dummies Questions & Answers
Hi.
I'm trying to copy multiple folders from the remote machine to the local machine. I wrote a batch file to run an ftp window.
The problem I am having is that the only command to copy files is mget *, and this copies only files, not folders.
For example, ftp ts555
cd ts555/test
' test... (5 Replies)
Discussion started by: leenyburger
5 Replies
4. UNIX for Dummies Questions & Answers
Hi
Can someone tell me what are the differences between software and hardware raid ?
thx for help. (2 Replies)
Discussion started by: presul
2 Replies
5. Linux
hello
my centOS newly installed system loading dmraid modules on startup
I did remove all LVM/raid things from system installation menus and after installation too but dmraid is still there
and he says: no raid disks found
also I did modprobe -r dm_raid45 and it do remove it but only until... (7 Replies)
Discussion started by: tip78
7 Replies
6. AIX
Hello,
I have a scsi pci x raid controller card on which I had created a disk array of 3 disks
when I type lspv ; I used to see 3 physical disks ( two local disks and one raid 5 disk )
suddenly the raid 5 disk array disappeared ; so the hardware engineer thought the problem was with SCSI... (0 Replies)
Discussion started by: filosophizer
0 Replies
7. Solaris
Server Model: T5120 with 146G x4 disks.
OS: Solaris 10 - installed on c1t0d0.
Plan to use software raid (veritas volume mgr) on c1t2d0 disk.
After format and label the disk, still not able to detect using vxdiskadm.
Question:
Should I remove the hardware raid on c1t2d0 first?
My... (4 Replies)
Discussion started by: KhawHL
4 Replies
8. Red Hat
Hello,
I want to delete a RAID configuration an old server has.
Since i haven't the chance to work with the specific raid controller in the past can you please help me how to perform the configuraiton?
I downloaded IBM ServeRAID Support CD but i wasn't able to configure the video card so i... (0 Replies)
Discussion started by: @dagio
0 Replies
LEARN ABOUT ULTRIX
reboot
reboot(8) System Manager's Manual reboot(8)
Name
reboot - automatic reboot procedures
Syntax
/etc/reboot [ -n ] [ -q ]
Description
The ULTRIX system is booted by loading a kernel image, usually into memory at location zero and transferring to zero. Because the system
is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.
When the reboot of a running system is desired, is normally used. If there are no users, can be used. The command causes the disks to be
synced, and then a multiuser reboot is initiated. The system is booted and an automatic disk check is performed. If the procedure suc-
ceeds, the system is then brought up for the users.
The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system. A consistency check
of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.
Options
-n Prevents the disks from being synced.
-q Reboots quickly and ungracefully, without shutting down running processes first.
Files
System code
See Also
crash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)
reboot(8)