So you want a log of the ups and downs of your DSL connection? Depending on your ping version (ping -V, mine is "ping utility, iputils-s20180629"), a single command might suffice:
Code:
ping -Di5 router
PING router.domain.De (192.168.0.1) 56(84) bytes of data.
[1547335266.088652] 64 bytes from router.domain.De (192.168.0.1): icmp_seq=1 ttl=64 time=1.67 ms
[1547335271.094225] 64 bytes from router.domain.De (192.168.0.1): icmp_seq=2 ttl=64 time=1.44 ms
[1547335276.099867] 64 bytes from router.domain.De (192.168.0.1): icmp_seq=3 ttl=64 time=1.48 ms
Adapt the interval (-i) value to the desired granularity.
suse linux 6.4 im running and i have port 110 for pop and smtp open, i have set up some email addresses for my friends, but they recieve errors saying that relaying is denied. i know this is to prevent spamming software from using my domain to send spam, but how do i let my users send their mail?... (6 Replies)
hey guys
Do you guys know of a good way that I can combine and load balance my 2 Internet connections using a Linux or Bsd box? Would LVS be able to do this?
Thanks in advance (1 Reply)
I'm running FreeBSD 6.2 and suddenly lost connectivity to the net. After unplugging the router and checking all the connections I could find nothing wrong. All the driver software seems to be intact. I thought I would remove the driver software and restore it. However, when I go to root and type
... (5 Replies)
Hi
I have a question related to load balancing.I have two separate internet connections with 2Mbps speed and i would like to aggregate this two connections intro one connection with 4Mbps.Is it possible to do that, to put a Linux or Unix machine as a gateway?I read some stuff to split the... (3 Replies)
I had a purge of applications on my Ubuntu 8.10 install and lost the above mentioned icon from the toolbar, yes I know I should have left it alone!
I have managed to find and install a shutdown icon and a separate shutdown, restart,etc icon uing the synaptic package manager but they are not the... (0 Replies)
I’m familiar with load balancing.. but Is it possible to actually bond multiple DSL lines together? I hear of ways to bond using MLPPP but that requires support from an ISP. Is there a way to actually bond without support from my ISP, or use say a cable modem and a DSL line together for faster... (0 Replies)
Dear all,
Hope you are all fine & enjoying your good health.
Look at this equation
1+1+1=3
So simple I just want to say that I have three internet connections of 1mb, 1mb & 1mb but I can use only 1mb connection at a time & other two connections are useless for me. But now I want to make all... (0 Replies)
How to make a log that will log all ips that connect to the server or send packets? And how to block an ip that make packets flood and try to DDoS? Thanks. (1 Reply)
Discussion started by: [xEF]Danger
1 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD April 11, 1998 BSD