Sponsored Content
Operating Systems Solaris Solaris link aggregation not working as expected Post 303028411 by MadeInGermany on Monday 7th of January 2019 03:03:13 PM
Old 01-07-2019
Then check LACP status with dladm show-aggr -L...
 

9 More Discussions You Might Find Interesting

1. Solaris

Link Aggregation

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (2 Replies)
Discussion started by: hcclnoodles
2 Replies

2. UNIX for Advanced & Expert Users

Link Aggregation and LACP

Hi there I have a requirement to provide failover to our customer boxes in case of interface / switch failure, I have been looking at Solaris Link Aggregation with LACP and I wanted to ask a question Ive seen multiple websites that say the following Does this also mean that if the... (1 Reply)
Discussion started by: hcclnoodles
1 Replies

3. AIX

Link aggregation with hacmp ?

Hi, I need to setup a hacmp cluster (my first one, we usually use VCS on AIX), but I require more network bandwith than a normal gigabit etherchannel setup can provide, so I am thinking about using linkaggregation - 2 active adapters to one switch and a single backup adapter to another switch... (4 Replies)
Discussion started by: zxmaus
4 Replies

4. Solaris

Link aggregation

Me again :) I'm trying to find a page describing the L2, L3 und L4 modes of dladm. It's nice to read "hashed by ip header", but how should I use that? On the file-server it's ok to have the six interfaces serving six clients each on it's own. But an rsync connection via switch between two... (8 Replies)
Discussion started by: PatrickBaer
8 Replies

5. Solaris

solaris link aggregation problem , once i reboot it is not showing, not able to ping the default gat

Hi All, I am trying to aggregate the NIC's,(igb2 and igb3) (igb0 is used by the physical system and igb1 is used by primary-vsw0) to create the domains on that for faster data transfer, I followed the process for creating the aggregation, dladm create-aggr -d igb2 -d igb3 1 after creating the... (2 Replies)
Discussion started by: buildscm
2 Replies

6. HP-UX

Break Link Aggregation in HP UX.

Hi, I want to Break the Link Aggregation. My aggregation are lan0+lan1 = lan900. Now I want to break this and put the IP in lan0. But i have cluster environment and this is the main database server. So It need to change in cluster script. But I dont know where I have to change it. Please... (1 Reply)
Discussion started by: mkiron
1 Replies

7. Solaris

Link Aggregation without LACP

Hi, I'm not from the Solaris world and some of these things are new to me. Can someone tell me if it is possible to configure link aggregation without using LACP? I am told etherchannel was setup without LACP. (3 Replies)
Discussion started by: techy1
3 Replies

8. Solaris

Link aggregation issues Solaris 10

I have setup link aggregation with 3 interfaces on my solaris 10 system. All looks good but my problem is that the traffic is only going out bge0 and not the other 2 links. bash-4.3# dladm show-aggr -s key:33 ipackets rbytes opackets obytes %ipkts %opkts ... (3 Replies)
Discussion started by: primeaup
3 Replies

9. IP Networking

Link Aggregation

Hi ihave three link of internet and iwant to put one linux front of a firewall that this three linux speard firewall such az load balance and fialover but dont close any port and protocol and only firewall have been internet what way can i use for it ? are there any script and services do that... (0 Replies)
Discussion started by: mnnn
0 Replies
pcwl(7D)							      Devices								  pcwl(7D)

NAME
pcwl - Lucent/PrismII 802.11b wireless NIC driver DESCRIPTION
The pcwl 802.11b wireless NIC driver is a multi- threaded, loadable, clonable, GLDv3-based STREAMS driver. It supports the pccard and PCI/MiniPCI cards with the Lucent and PrismII 802.11b chipsets on x86 and SPARC. DRIVER CONFIGURATION
The pcwl driver supports 802.11b data rates of 1, 2, 5.5 and 11 (Mbits/sec). The default is 11. The pcwl driver supports BSS networks (also known as "ap" or "infrastructure" networks) and IBSS (or "ad-hoc") networks. For authentication type, the pcwl driver supports the "open" (or "open-system") mode and the "shared-key" mode. For encryption type, only WEP is currently supported. You perform configuration and administration tasks using the dladm(1M) and wificonfig(1M) utilities. FILES
/dev/pcwl* Special character device. /kernel/drv/pcwl 32-bit ELF kernel module (x86). /kernel/drv/amd64/pcwl 64-bit ELF kernel module (x86). /kernel/drv/sparcv9/pcwl 64-bit ELF kernel module (SPARC). ATTRIBUTES
See attributes(5) for a description of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SPARC, x86 | +-----------------------------+-----------------------------+ SEE ALSO
dladm(1M), wificonfig(1M), attributes(5), gld(7D) 802.11b Standard for Wireless Local Area Networks (WLANs) - IEEE SunOS 5.11 24 Jan 2007 pcwl(7D)
All times are GMT -4. The time now is 05:15 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy