Will some one tell me what this means.
"warning: ida 0 <slot 6> : command timed out on dev 1/42 blk 4824290 logical unit=0 blocks=5512102, size 2, cmd=0x20."
I'm running SCO 505 on a proliant 1600r.
Thnank you in advance. (3 Replies)
I am using an Acer Aspire 4720Z with two partitions C and D. Windows is installed on C and I decided to install Red Hat Linux 9 in partition D. The two partitions are in NTFS file system. During my installation of the the Linux, a prompt was displayed on screen with the message: "No hard drives... (2 Replies)
I have a Solaris machine running OpenSolaris v5.11.
It came with a hard drive. It's called /dev/dsk/c4d0s0.
I added two new hard drives into the box. I can't figure out what it's called in /dev/dsk. There are 210 filenames in /dev/dsk.
How do I find out which filename corresponds to the... (2 Replies)
Version: solaris 10 x86
I just got a western digital external harddrive formated with fat 32. this drive came with some setup files which is meant for windows or mac.
I want to reformat and partition this drive into two ( for solaris and windows) such that the setup files will still be there... (2 Replies)
Folks;
I just added 2 physical new hard drives to my SUSE server. My server is already running SUSE 10.3 version.
Is there a command i can use to add the new space or even see if the system can sees them? (3 Replies)
I have a T2000 Sun-Fire server. I have 2 sets of drives in a raid 1. Lets call them Set A and Set B. I had Set A installed and working. I needed a new install so I so build up Set B. After some time I wanted to put Set A back in the server. Now the system will not boot off of Set A. I tried to boot... (7 Replies)
Hello everyone. I have a question which I may know the answer to, I'm just looking for a confirmation. When it comes to the MBR of a hard drive, i've read in multiple sources that it's always located in the first sector of the hard drive. Is the MBR there from the factory? When I buy a new blank... (3 Replies)
I have three Sun Oracle Netra T5220s. I am trying to just get the processor information psrinfo or prtdiag -v from the # prompt in single user mode.
I am needing to know the commands to get to boot the CD/DVD of the Solaris OS. I am using it via Serial Port Management.
Tinkering around I... (4 Replies)
Hello,
I have install 2 HDD in my server and now installing the Centos6.4.
I want create the LVM of those 2 HDD's so while i'm doing this it is not allowing me to select these 2 disk's from allowable disk list.
Same problem if i tried to make Software RAID with creating LVM.
Please help. (1 Reply)
Hi,
I have two SCSI Hard Drives in a Sun Solaris 8 server as shown below. I would like to access Disk1 and look at its contents, directory structure and files. How do I change my default directory from Disk 0 to Disk 1 and vice versa?
Thank you. (5 Replies)
Discussion started by: ssabet
5 Replies
LEARN ABOUT CENTOS
mkfs.minix
MKFS.MINIX(8) System Administration MKFS.MINIX(8)NAME
mkfs.minix - make a Minix filesystem
SYNOPSIS
mkfs.minix [-c|-l filename] [-n namelength] [-i inodecount] [-v] device [size-in-blocks]
DESCRIPTION
mkfs.minix creates a Linux MINIX filesystem on a device (usually a disk partition).
The device is usually of the following form:
/dev/hda[1-8] (IDE disk 1)
/dev/hdb[1-8] (IDE disk 2)
/dev/sda[1-8] (SCSI disk 1)
/dev/sdb[1-8] (SCSI disk 2)
The size-in-blocks parameter is the desired size of the file system, in blocks. It is present only for backwards compatibility. If omit-
ted the size will be determined automatically. Only block counts strictly greater than 10 and strictly less than 65536 are allowed.
OPTIONS -c Check the device for bad blocks before creating the filesystem. If any are found, the count is printed.
-n namelength
Specify the maximum length of filenames. Currently, the only allowable values are 14 and 30. The default is 30. Note that kernels
older than 0.99p7 only accept namelength 14.
-i inodecount
Specify the number of inodes for the filesystem.
-l filename
Read the list of bad blocks from filename. The file has one bad-block number per line. The count of bad blocks read is printed.
-1 Make a Minix version 1 filesystem.
-2, -v Make a Minix version 2 filesystem.
-3 Make a Minix version 3 filesystem.
EXIT CODES
The exit code returned by mkfs.minix is one of the following:
0 No errors
8 Operational error
16 Usage or syntax error
SEE ALSO mkfs(8), fsck(8), reboot(8)AVAILABILITY
The mkfs.minix command is part of the util-linux package and is available from ftp://ftp.kernel.org/pub/linux/utils/util-linux/.
util-linux June 2011 MKFS.MINIX(8)