12-25-2018
Quote:
Note: Newbie to IBM virtualization :-)
Query: Created a new AIX7.1 lpar on a system with same config as one before however the new one is having issues going out to physical network.
There are such a number of possible causes to this that we will need to narrow it down a bit first. Here is how (in general) AIX virtualisation in respect to networks work:
You have one (if you have IVM, two if you have a HMC) VIOS servers in each hardware box. "VIOS" means "virtual I/O server") and these are LPARs running a special version of AIX (called "IOS") used to virtualise hardware which can't easily be virtualised otherwise, i.e. network cards. That means: you have VIOS servers which have the physical network card(s) assigned as ressources. In the VIOS you create a virtual network card which is based on some physical connection (a quite common setup is to have Etherchannels consisting of several physical network cards bonded and base the virtual adapter on that) and this virtrual card is given to the LPAR as a resource. The VIOS acts as a bridge with an internal VLAN system so that it can redirect cleanly the traffic to/from the various LPARs it serves.
So, first question: did you create a new virtual adapter in the VIOS when you created the new LPAR?
Second: you need to configure the VLANs for inside and outside the phyiscal system where the LPAR is based on correctly for the network connection to work. If you need help with this you will need to tell us a bit more about your network, its VLANs and the configuration of the NIC in the VIOS as shown in the HMC/IVM.
I hope this helps.
bakunin
10 More Discussions You Might Find Interesting
1. AIX
Hi,
I define 2 new LV on the vio server and run a cfgmgr on the partition and see my 2 new hdisk (hdisk6 and hdisk7).
I extend my vg vg000 (on the partition) and add the 2 hdisks.
I had a filesystem on the vg000 and when I added the disk I would like to increase the filesystem. But I cannot do a... (0 Replies)
Discussion started by: touny
0 Replies
2. HP-UX
Hello all,
I want to add a new virtual interface on HP-UX B.11.11 U 9000/800 box.
I know that ifconfig can be used to add the Virtual interface.
BUt i do not know the exact syntax. it some times gives plumb error if i try to add
# ifconfig vif0 10.1.10.1 up
plumb error: No such file... (3 Replies)
Discussion started by: supersumanth
3 Replies
3. HP-UX
Hello all,
I have configured a virtual interface using ifconfig on HP UX 11.11.
When i try to do traceroute with -i option i get * * * from traceroute.
i use $traceroute -i lan0:1 my-gateway
traceroute to my-gateway (15.70.180.1), 30 hops max, 40 byte packets
1 * * *
2 * * *
30 * *... (2 Replies)
Discussion started by: supersumanth
2 Replies
4. Shell Programming and Scripting
How would i create virtual interface in linux to configure more than one IP address for a physical interface?
any help wll be appreciated.
https://www.unix.com/images/misc/progress.gif (1 Reply)
Discussion started by: salil2012
1 Replies
5. AIX
Hi,
I am totally new to AIX. I would like to know how to create virtual interface on AIX machine.
Thanks,
Pooja (4 Replies)
Discussion started by: pooja84k
4 Replies
6. AIX
I just wondering if there are ways to open multiple virtual terminal to a single LPAR.
After I have use putty to login to the VIOS. I will use mkvt -id <LPAR id> to open console but if my friend want to open 2 second one, it will say, VT already connected.
IS there a way to work this around ? ... (1 Reply)
Discussion started by: wingcross
1 Replies
7. AIX
Hello, hopefully someone can help me out with this, I have created a virtual Ethernet adapter on the VIO but would like to add it to my new LPAR.
On my VIO only my disk is mapped.
$ lsmap -all
SVSA Physloc Client Partition ID
--------------- --------------------------------------------... (5 Replies)
Discussion started by: audis$
5 Replies
8. AIX
Hi,
When i'am taking nmon report I am missing the LPAR tab that shows CPU and Shared CPU utilization.
My OS version is 6100-06-05-1115
Topas_nmon
Kindly suggest and help me to sort out this issue. (3 Replies)
Discussion started by: Mohamed Thamim
3 Replies
9. AIX
Hello,
VIOS 2.2.1.4 using IVM.
I'm trying to extend a virtual disk assigned to a running lpar so that I can expand the lpar's datavg and grow some filesystems for the user.
Storage admin expanded the lun and new size was reflected in VIO right away. I then needed the storage pool to... (2 Replies)
Discussion started by: j_aix
2 Replies
10. AIX
Hello,
Is there a way to run
xclock
or
startx
on LPAR, since LPAR doesn't have any console or it is connected to HMC
usually the way is to export the display to some PC which has Xmanager running on it, but in my case, I want to run xmanager on the AIX Lpar and run on it the... (2 Replies)
Discussion started by: filosophizer
2 Replies
LEARN ABOUT OPENSOLARIS
systemd-networkd
SYSTEMD-NETWORKD.SERVICE(8) systemd-networkd.service SYSTEMD-NETWORKD.SERVICE(8)
NAME
systemd-networkd.service, systemd-networkd - Network manager
SYNOPSIS
systemd-networkd.service
/lib/systemd/systemd-networkd
DESCRIPTION
systemd-networkd is a system service that manages networks. It detects and configures network devices as they appear, as well as creating
virtual network devices.
To configure low-level link settings independently of networks, see systemd.link(5).
systemd-networkd will create network devices based on the configuration in systemd.netdev(5) files, respecting the [Match] sections in
those files.
systemd-networkd will manage network addresses and routes for any link for which it finds a .network file with an appropriate [Match]
section, see systemd.network(5). For those links, it will flush existing network addresses and routes when bringing up the device. Any
links not matched by one of the .network files will be ignored. It is also possible to explicitly tell systemd-networkd to ignore a link by
using Unmanaged=yes option, see systemd.network(5).
When systemd-networkd exits, it generally leaves existing network devices and configuration intact. This makes it possible to transition
from the initrams and to restart the service without breaking connectivity. This also means that when configuration is updated and
systemd-networkd is restarted, netdev interfaces for which configuration was removed will not be dropped, and may need to be cleaned up
manually.
CONFIGURATION FILES
The configuration files are read from the files located in the system network directory /lib/systemd/network, the volatile runtime network
directory /run/systemd/network and the local administration network directory /etc/systemd/network.
Networks are configured in .network files, see systemd.network(5), and virtual network devices are configured in .netdev files, see
systemd.netdev(5).
SEE ALSO
systemd(1), systemd.link(5), systemd.network(5), systemd.netdev(5), systemd-networkd-wait-online.service(8)
systemd 237 SYSTEMD-NETWORKD.SERVICE(8)