12-12-2018
Naturally 0.00094 is zero when truncated to three fixed decimal places. That is not "edge case" -- it's supposed to do that.
If you want more decimal points in my code, change DP and MOD.
7 More Discussions You Might Find Interesting
1. UNIX for Advanced & Expert Users
Anyone know of a guide or instructions for Solaris
I got to configure a SBUS HBA to talk to a tape robot.
I have done this on a switch but not point to point.
just going HBA >>>>> TAPE Fibre simple two nodes
Kie (6 Replies)
Discussion started by: kie
6 Replies
2. UNIX for Dummies Questions & Answers
Hi!
I'm new in these forums and more or less new with Unix. So... here is the question:
does anyone know where is redirected the output of a command when you put >&- after it?
Does it means any standard file descriptor?
Thanks! (2 Replies)
Discussion started by: csecnarf
2 Replies
3. Shell Programming and Scripting
hi,
I would like to ask or is it possible to dump a hex using dd from starting point to end point just like the "xxd -s 512 -l 512 <bin file>"
I know the redirect hexdump -C but i can't figure it out the combination options of dd.
Hope someone can share their knowledge..
Thanks in... (3 Replies)
Discussion started by: jao_madn
3 Replies
4. Post Here to Contact Site Administrators and Moderators
HI Everyone,
I have below source file
AAA|NAME1|ADDRESS1|300.20
BBB|NAME2|ADDRESS2|400.31
CCC|NAME3|ADDRESS3|300.34
I have requirement where I need to sum up fourth field in above fixed width pipe delimited flat file. When I use below code, it gives me value 1001.00
But I am expecting... (1 Reply)
Discussion started by: patricjemmy6
1 Replies
5. Shell Programming and Scripting
Hey all! :)
I'm trying to create a fixed mount point for an usb cardreader.
I've found a script on a raspberry pi forum which does the following:
usb stick is plugged in -> script checks the mount point for data -> script starts copying the files automatically -> script unmounts the... (0 Replies)
Discussion started by: Eomer
0 Replies
6. UNIX for Beginners Questions & Answers
How to create a new mount point with 600GB and add 350 GBexisting mount point
Best if there step that i can follow or execute before i mount or add diskspace IN AIX
Thanks (2 Replies)
Discussion started by: Thilagarajan
2 Replies
7. Shell Programming and Scripting
Well, guys I saw a question about GOTO for Python.
So this gave me the inspiration to attempt a GOTO function for 'dash', (bash and ksh too).
Machine: MBP OSX 10.14.3, default bash terminal, calling '#!/usr/local/bin/dash'...
This is purely a fun project to see if it is possible in PURE... (3 Replies)
Discussion started by: wisecracker
3 Replies
LEARN ABOUT OSF1
dxmcolormixsetnewcolor
DXmColorMixSetNewColor(3X) DXmColorMixSetNewColor(3X)
NAME
DXmColorMixSetNewColor - Sets the new color red, green, and blue values in the color mixing widget.
SYNOPSIS
void DXmColorMixSetNewColor(
DXmColorMixWidget cmw,
unsigned short red,
unsigned short green,
unsigned short blue );
PARAMETERS
The identifier (widget ID) of the color mixing widget. The new color red value. The value is expressed as an X color value (0 to 65535).
The new color green value. The value is expressed as an X color value (0 to 65535). The new color blue value. The value is expressed as an
X color value (0 to 65535).
A complete list of all the X color values available to you is located on your system. To find it, type the following command: % find /
-name '*rgb*' -print
DESCRIPTION
The DXmColorMixSetNewColor routine allows the application or a user-supplied color mixer subwidget to pass the current color value to the
color mixing widget. Note that your application will perform this operation faster if you call this routine instead of the Intrinsic rou-
tine XtSetValues.
SEE ALSO
DXmColorMixGetNewColor(3X), DXmCreateColorMix(3X), DXmCreateColorMixDialog(3X)
DXmColorMixSetNewColor(3X)