Sponsored Content
Operating Systems Solaris Any hope for this bootlooping Sun V210? Post 303026773 by gull04 on Monday 3rd of December 2018 07:52:09 AM
Old 12-03-2018
Hi Vext01,

As you've had the machine in bits and have replaced the guts, I'm going to stick my neck out and suggest that the connections should be good as they should all have been re-seated during component changes. I'd maybe tempted to swap the PSU if you have one, but the maintenance indicator would generally be on if it was faulty.

It might be that just pulling and re-seating the power supply would be enough.

I'm kind of running out of steam on this, you've changed the MOBO and the CPU's. The fault has remained pretty consistent, from the environmentals it doesn't seem to be power related. I'ts unlikely that this will make any difference, but can you capture the ALOM config and then run a sc> resetsc you'll have to go through the setting up the ALOM again (Although you should just need to change the password as the rest should work).

Additionally something has just come to the fore, didn't happen to me - it was an engineer that I worked with. He had a fault on a v210 or it may have been a v240 - where he replaced the Mother Board and couldn't get to the ok prompt.

Turned out that he'd mixed the matched pairs of memory and that causes the OBP not to start, it didn't supply an error message either - I've been in touch with him and although the Dimm's were the same speed - they had different manufacturers and that was enough.


Regards

Gull04

Last edited by gull04; 12-03-2018 at 09:29 AM.. Reason: More Info
 

7 More Discussions You Might Find Interesting

1. Solaris

Sun Fire v210 display card

hi all, how can install a display card on a sun fire v210. regards. marcel (2 Replies)
Discussion started by: marcelious
2 Replies

2. Solaris

V210 to V440

I recently acquired a server for home use. Currently, I'm running a V210. I was wondering of a way to basically swap hard drives into the V440. I would like to avoid reinstall on the V440 for many reasons. Currently on the V440, when I try to boot up it forces itself into System Maintenance... (1 Reply)
Discussion started by: adelsin
1 Replies

3. Solaris

V210 to V440

I'm currently trying to move a perfectly find harddrive from a V210 to a V440. From what I can tell, the disk labeling a bit different, (V210 is c1t0d0 and V440 is c0t0d0). My question is, what all do I have to change to get the V440 to boot off of this with very little complications. Right now, it... (21 Replies)
Discussion started by: adelsin
21 Replies

4. Solaris

Booting error in Sun V210

Sun Fire V210, No Keyboard Copyright 1998-2003 Sun Microsystems, Inc. All rights reserved. OpenBoot 4.13.2, 4096 MB memory installed, Serial #61203679. Ethernet address 0:3:ba:a5:e4:df, Host ID: 83a5e4df. Boot device: net File and args: 100 Mbps FDX Link up Timeout waiting for... (5 Replies)
Discussion started by: Mrudhul
5 Replies

5. Solaris

Connect using ALOM to Sun Fire V210

I have bought from eBay a second hand Sun Fire V210 server and I'm really stumped at the lack of complete instructions on how to connect to it. I don't have a Windows machine, I've only got Ubuntu and OS X computers. None of them have an old RS-232 port on them either. In saying that, I have... (12 Replies)
Discussion started by: danijeljames
12 Replies

6. UNIX for Dummies Questions & Answers

New to Forum & Sun Surefire V210 Access

Purchased a Sun Surefire V210 Server off eBay. Unable to Access the Terminal Mode via the Terminal MGT. Using Windows 7 home, and downloaded the ConEmu. The ConEmu brings up a Command line on the PC, and that's it. Being new to all this, I was expecting a Login prompt to pop up. Read the... (22 Replies)
Discussion started by: screenprintr
22 Replies

7. Solaris

Sun Fire V210 CPU Fan Temp too high?

Hey, I have a V210 with a failed CPU fan. The temperature is currently at 84C and I've been asked to wait a few weeks before replacing as its a production system and it cant be shut down yet. Is it too hot? Do I risk killing the CPU at this temp? Its been like this for a few weeks now... (5 Replies)
Discussion started by: magarvo
5 Replies
Info::Layer3::Sun(3pm)					User Contributed Perl Documentation				    Info::Layer3::Sun(3pm)

NAME
SNMP::Info::Layer3::Sun - SNMP Interface to L3 Sun Solaris AUTHOR
begemot SYNOPSIS
# Let SNMP::Info determine the correct subclass for you. my $sun = new SNMP::Info( AutoSpecify => 1, Debug => 1, DestHost => 'mysunrouter', Community => 'public', Version => 1 ) or die "Can't connect to DestHost. "; my $class = $sun->class(); print "SNMP::Info determined this device to fall under subclass : $class "; DESCRIPTION
Subclass for Generic Sun Routers running SunOS Inherited Classes SNMP::Info::Layer3 Required MIBs Inherited Classes' MIBs See "Required MIBs" in SNMP::Info::Layer3 for its own MIB requirements. GLOBALS
These are methods that return scalar value from SNMP $sun->vendor() Returns 'sun' $sun->os() Returns 'sun' $sun->os_ver() Returns the software version extracted from message of the day. $sun->model() Returns 'Solaris Router' $sun->serial() Returns serial number Globals imported from SNMP::Info::Layer3 See documentation in "GLOBALS" in SNMP::Info::Layer3 for details. TABLE METHODS
These are methods that return tables of information in the form of a reference to a hash. Overrides $sun->i_ignore() Returns reference to hash. Increments value of IID if port is to be ignored. Ignores loopback Table Methods imported from SNMP::Info::Layer3 See documentation in "TABLE METHODS" in SNMP::Info::Layer3 for details. perl v5.12.4 2011-09-28 Info::Layer3::Sun(3pm)
All times are GMT -4. The time now is 06:23 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy