11-30-2018
Things are getting a little more convoluted in my head, and I know that with SCO it is vital to perform the correct steps in the correct order. I am sure I'm not doing that, so I need some more help. With the new server hardware, the CD drive is actually an IDE device, connected to the IDE port on the mb. The HD is connected to SATA port that is emulating IDE. In BIOS when I look at the Boot order, it shows my HD as IDE 0, and my CD as just IDE, so I'm assuming it is the Secondary Master with respect to the IDE terminology. The CD drive in the old server was also attached as the Secondary Master IDE, but I guess that the old settings need to be replaced by new settings by using "mkdev cdrom"? I have been trying to do this, first I performed the removal of the CD drive in mkdev, but I did not rebuild the kernel and reboot - I just immediately tried to add the CD drive again and I got the message saying there was already a CD Rom device at that location. Do I need to reboot after each step of this process, and am I even doing the right thing? If I get it done correctly, is this the right command to mount the CD: mount /dev/cd0 /mnt? Thanks for all your help and patience with me.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. UNIX for Advanced & Expert Users
I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies
4. UNIX for Dummies Questions & Answers
hello guys.
I just installed SCO 5.0.6 OpenServer it went all the way to the end of the installation and the first boot try it gave me this message.
not a directory
boot not found
cannot open
stage 1 boot failure: error loading hd (40)/boot (2 Replies)
Discussion started by: josramon
2 Replies
5. SCO
Which version of Ethereal can I use for SCO OpenServer 5.0.7??? (0 Replies)
Discussion started by: bean2
0 Replies
6. UNIX for Dummies Questions & Answers
Hi there guys.
I just got this new SCO version and i'm having some problem printing from shell,
This is what i'm typing at the # sign : lp -dHP /etc/hosts and it prints no problem but when i use any other user at the $ sign it gives me this error.
/dev/fd/7: /usr/lib/lp/sysv/7: not found.
... (1 Reply)
Discussion started by: josramon
1 Replies
7. UNIX for Dummies Questions & Answers
Hi guys,
I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies
8. SCO
Dear members
when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config.
i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Discussion started by: M_farooqui
0 Replies
9. SCO
Hi,
I have an openserver 5.0.0 machine in the office. The sysad of that machine left years ago without leaving the password to anyone.
I was wondering if someone has a copy of the boot / root diskettes (rescue) for this version? Or perhaps if anyone knows a download link / location in the... (0 Replies)
Discussion started by: marcpascual
0 Replies
10. SCO
I need SCO Openserver 4.2. Please, give me distributive of that version SCO:eek: (0 Replies)
Discussion started by: caine
0 Replies
HD(4) Linux Programmer's Manual HD(4)
NAME
hd - MFM/IDE hard disk devices
DESCRIPTION
The hd* devices are block devices to access MFM/IDE hard disk drives in raw mode. The master drive on the primary IDE controller (major
device number 3) is hda; the slave drive is hdb. The master drive of the second controller (major device number 22) is hdc and the slave
hdd.
General IDE block device names have the form hdX, or hdXP, where X is a letter denoting the physical drive, and P is a number denoting the
partition on that physical drive. The first form, hdX, is used to address the whole drive. Partition numbers are assigned in the order
the partitions are discovered, and only nonempty, nonextended partitions get a number. However, partition numbers 1-4 are given to the
four partitions described in the MBR (the "primary" partitions), regardless of whether they are unused or extended. Thus, the first logi-
cal partition will be hdX5. Both DOS-type partitioning and BSD-disklabel partitioning are supported. You can have at most 63 partitions
on an IDE disk.
For example, /dev/hda refers to all of the first IDE drive in the system; and /dev/hdb3 refers to the third DOS "primary" partition on the
second one.
They are typically created by:
mknod -m 660 /dev/hda b 3 0
mknod -m 660 /dev/hda1 b 3 1
mknod -m 660 /dev/hda2 b 3 2
...
mknod -m 660 /dev/hda8 b 3 8
mknod -m 660 /dev/hdb b 3 64
mknod -m 660 /dev/hdb1 b 3 65
mknod -m 660 /dev/hdb2 b 3 66
...
mknod -m 660 /dev/hdb8 b 3 72
chown root:disk /dev/hd*
FILES
/dev/hd*
SEE ALSO
chown(1), mknod(1), sd(4), mount(8)
COLOPHON
This page is part of release 3.27 of the Linux man-pages project. A description of the project, and information about reporting bugs, can
be found at http://www.kernel.org/doc/man-pages/.
Linux 1992-12-17 HD(4)