Can you please post output of the following on the server :
Also, can you run the following from client unable to connect (presuming clients are linux boxes)..
Are you using VPN or behind firewalls ?
Regards
Peasant.
Last edited by Peasant; 11-22-2018 at 11:56 AM..
Reason: Typos
Hi,
I have a solaris 8 machine.
I see ssh is running in the machine
sbnismwp2# ps -aef | grep ssh
root 947 945 0 04:34:45 ? 0:00 /export/opt/SSHtecagt/sbin/ssh-mgmt-sysmonitor
root 945 1 0 04:34:45 ? 0:00 /export/opt/SSHtecagt/sbin/ssh-mgmt-agent... (11 Replies)
I try to transfer a file from a Linux host to an AIX-host via scp, which fails. Logging into the AIX-system from the same Linux-system via ssh works well and i am a bit at a loss where to look.
The original setup was with a user account provided via LDAP, but because of the error message (see... (4 Replies)
Hi All,
I have a setup of around 100 servers with atleast 10 users on each box.The public key from one server has been created and updated on all other servers , so that passwordless login can be done from any use.
We recently had a problem that ssh keys on one of the system was changed and... (2 Replies)
Dear expert,
I have gone through the thread
A similar error arising for me , please find the debug logs.
I have tried from another server to push a file using scp but not working for me.
i am using SunOS SUNW,SPARC-Enterprise machine.
Thanks (5 Replies)
Dear,
I hope you all will be ok.
I have an issue with Solaris box running on x86 Blade.
I am unable to ping a node neither traceroute. I am able to do traceroute from oce0:6 port which have IP and subnet of same type which oce0:1 has.
details are as follows:
Problem:
root@rinams02:/#... (3 Replies)
I know the "how to setup passwordless SSH" question is asked probably 5 times a week.
I know how to setup passwordless SSH, it's not tough, however after reinstalling linux on my server, I found a problem. I could SSH into my server just fine, no password required, however SCP still required a... (4 Replies)
I still haven't had chance to read the entire Debian manual, which I promise I will do as soon as I can, and I will start putting info back into this forum.
However, for the mean time, could someone please help with a small script? I understand what I've got to do and how to do it, but I'm... (13 Replies)
root@PRD /> rsh DR
KFAFH_DR: protocol failure due to unexpected closure from server end
root@PRD /> telnet DR
Trying...
Connected to DR.
Escape character is '^]'.
Connection closed.
root@PRD /> ftp DR
Connected to KFAFH_DR.
421 Service not available, remote server has closed connection... (2 Replies)
Discussion started by: filosophizer
2 Replies
LEARN ABOUT DEBIAN
mrtg-ping-probe
MRTG-PING-PROBE(1) General Commands Manual MRTG-PING-PROBE(1)NAME
mrtg-ping-probe - ping probe module for Multi Router Traffic Grapher
DESCRIPTION
mrtg-ping-probe is a ping probe module for MRTG 2.x. It is used to monitor the round trip time and packet loss to networked devices. MRTG
uses the output of mrtg-ping-probe to generate graphs visualizing minimum and maximum round trip times or packet loss.
mrtg-ping-probe is not run directly, but is called by MRTG as a helper when it needs to determine ping time to a host.
Act responsibly: do not use mrtg-ping-probe to ping devices without the owner's permission. Just imagine if 10,000 people decided to ping
your hosts! mrtg-ping-probe is meant to be used within your network to get round trip time performance figures for your network.
OPTIONS
To use mrtg-ping-probe you need to configure MRTG to call it from within the definition of a target host. This is done in the MRTG config
file, which is usually /etc/mrtg.conf.
Here's an example snippet: change the target name and IP address to suit your needs.
Target[your.target.ping]: `/usr/bin/mrtg-ping-probe 123.456.789.123`
SetEnv[your.target.ping]: MRTG_INT_IP="123.456.789.123" MRTG_INT_DESCR="ping"
MaxBytes[your.target.ping]: 100
AbsMax[your.target.ping]: 200
Options[your.target.ping]: gauge, growright
YLegend[your.target.ping]: ping time (ms)
ShortLegend[your.target.ping]: ms
Legend1[your.target.ping]: Maximum Round Trip Time in ms
Legend2[your.target.ping]: Minimum Round Trip Time in ms
Legend3[your.target.ping]: Maximal 5 Minute Maximum Round Trip Time in ms
Legend4[your.target.ping]: Maximal 5 Minute Minimum Round Trip Time in ms
LegendI[your.target.ping]: Max:
LegendO[your.target.ping]: Min:
Pay close attention to the backticks in the first line which tell MRTG to execute the nominated external program. Note also that you need
to use the "gauge" option, since the results of subsequent ping probes are independant values and not an incrementing counter.
SEE ALSO mrtg(1).
The latest release of mrtg-ping-probe can be found on the web at http://pwo.de/projects/mrtg/
AUTHOR
This manual page was written by Jonathan Oxer <jon@debian.org>, for the Debian project (but may be used by others).
April 14, 2003 MRTG-PING-PROBE(1)