I am new to UNIX and have been trying to add DNS servers so I can access the internet under Solaris 9. I am using a static IP and have the subnet and gateway configured but cannot figure out to add DNS servers. Does anyone know how to do this? Thank you very much for any help. (1 Reply)
Hello evrybody
I need to know how i can implement and configure DNS server in solaris9 and i need to understand which files i modified it to do that
Thanks all (8 Replies)
hey guys, how to add soalris box as a microsoft DNS Client ?
and how to register in the microsoft DNS ??
i managed to query from the DNS server after adding /etc/resolve.conf and editing /etc/nsswitch.conf
but i need to register the soalris server (dns Client) into Microsoft DNS automatically.... (3 Replies)
Hi all,
What is the procedure to add a client to a DNS server.
what are the settings and files need to be added/changed ?
thanks in advance! (6 Replies)
Hi all,
I have some sort of problem with BIND DNS server my environment as follows.
bash-3.00# cat /etc/release
Solaris 10 6/06 s10s_u2wos_09a SPARC
Copyright 2006 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to... (3 Replies)
Hello,
I have task to make a program that multiplies polynomials as client(input/output indexes)-server(multiplying) using RPC. However when I try to compile it with gcc it gives the next info:
for client:
Udefined first
symbol referenced
Clnt_create client.o
for server:
Udefined first... (5 Replies)
Hi folks,
I am attempting to setup a Solaris 10 syslog server to receive logs from linux machines. Here's what I did:
On the server (SunOS sun226 5.10), IP address: 192.168.212.226:
1. start syslogdby issuing $/usr/sbin/syslogd -T
On a client (SunOS sun221 5.8):
1. Configured... (1 Reply)
Hi,
We have built a new server (RHEL VM)and added that IP/hostname into dns zone configs file on DNS server (Solaris 10). Reloaded the configuration using
and added nameserver into resolv.conf on client. But when I am trying nslookup, its not getting resolved. The nameserver is not able to... (8 Replies)
Discussion started by: snchaudhari2
8 Replies
LEARN ABOUT FREEBSD
nos-tun
NOS-TUN(8) BSD System Manager's Manual NOS-TUN(8)NAME
nos-tun -- implement ``nos'' or ``ka9q'' style IP over IP tunnel
SYNOPSIS
nos-tun -t tunnel -s source -d destination -p protocol_number [source] target
DESCRIPTION
The nos-tun utility is used to establish an nos style tunnel, (also known as ka9q or IP-IP tunnel) using a tun(4) kernel interface.
Tunnel is the name of the tunnel device /dev/tun0 for example.
Source and destination are the addresses used on the tunnel device. If you configure the tunnel against a cisco router, use a netmask of
``255.255.255.252'' on the cisco. This is because the tunnel is a point-to-point interface in the FreeBSD end, a concept cisco does not
really implement.
Protocol number sets tunnel mode. Original KA9Q NOS uses 94 but many people use 4 on the worldwide backbone of ampr.org.
Target is the address of the remote tunnel device, this must match the source address set on the remote end.
EXAMPLES
This end, a FreeBSD box on address 192.168.59.34:
nos-tun -t /dev/tun0 -s 192.168.61.1 -d 192.168.61.2 192.168.56.45
Remote cisco on address 192.168.56.45:
interface tunnel 0
ip address 192.168.61.2 255.255.255.252
tunnel mode nos
tunnel destination 192.168.59.34
tunnel source 192.168.56.45
AUTHORS
Nickolay N. Dudorov <nnd@itfs.nsk.su> wrote the program, Poul-Henning Kamp <phk@FreeBSD.org> wrote the man-page. Isao SEKI
<iseki@gongon.com> added a new flag, IP protocol number.
BUGS
We do not allow for setting our source address for multihomed machines.
BSD April 11, 1998 BSD