I am new to UNIX and have been trying to add DNS servers so I can access the internet under Solaris 9. I am using a static IP and have the subnet and gateway configured but cannot figure out to add DNS servers. Does anyone know how to do this? Thank you very much for any help. (1 Reply)
Hello evrybody
I need to know how i can implement and configure DNS server in solaris9 and i need to understand which files i modified it to do that
Thanks all (8 Replies)
hey guys, how to add soalris box as a microsoft DNS Client ?
and how to register in the microsoft DNS ??
i managed to query from the DNS server after adding /etc/resolve.conf and editing /etc/nsswitch.conf
but i need to register the soalris server (dns Client) into Microsoft DNS automatically.... (3 Replies)
Hi all,
What is the procedure to add a client to a DNS server.
what are the settings and files need to be added/changed ?
thanks in advance! (6 Replies)
Hi all,
I have some sort of problem with BIND DNS server my environment as follows.
bash-3.00# cat /etc/release
Solaris 10 6/06 s10s_u2wos_09a SPARC
Copyright 2006 Sun Microsystems, Inc. All Rights Reserved.
Use is subject to... (3 Replies)
Hello,
I have task to make a program that multiplies polynomials as client(input/output indexes)-server(multiplying) using RPC. However when I try to compile it with gcc it gives the next info:
for client:
Udefined first
symbol referenced
Clnt_create client.o
for server:
Udefined first... (5 Replies)
Hi folks,
I am attempting to setup a Solaris 10 syslog server to receive logs from linux machines. Here's what I did:
On the server (SunOS sun226 5.10), IP address: 192.168.212.226:
1. start syslogdby issuing $/usr/sbin/syslogd -T
On a client (SunOS sun221 5.8):
1. Configured... (1 Reply)
Hi,
We have built a new server (RHEL VM)and added that IP/hostname into dns zone configs file on DNS server (Solaris 10). Reloaded the configuration using
and added nameserver into resolv.conf on client. But when I am trying nslookup, its not getting resolved. The nameserver is not able to... (8 Replies)
Discussion started by: snchaudhari2
8 Replies
LEARN ABOUT SUSE
ifndp-proxy
IFNDP-PROXY(5) Network configuration IFNDP-PROXY(5)NAME
ifndp-proxy[-<interface name>] - IPv6 NDP and IPv4 ARP proxy entries
SYNOPSIS
/etc/sysconfig/network/ifndp-proxy
/etc/sysconfig/network/ifndp-proxy-<interface name>
DESCRIPTION
These files contain IPv6 NDP and IPv4 ARP proxy settings, that should be applied using the ip neigh add proxy command documented in the
ip(8) manual page that provides a common interface for IPv4 and IPv6.
The NDP/ARP proxy is required, e.g. when IP addresses from the same subnet have to be used on the interface of the host as well as on
interfaces behind a (tunnel) interface and using a bridge is not an option.
Don't forget to enable forwarding and the NDP/ARP proxy by setting
net.ipv6.conf.<all|default|interface name>.proxy_ndp = 1
net.ipv6.conf.<all|default|interface name>.forwarding = 1
and/or
net.ipv4.conf.<all|default|interface name>.proxy_arp = 1
net.ipv4.conf.<all|default|interface name>.forwarding = 1
or
net.ipv4.ip_forward = 1
either as global all setting in the /etc/sysctl.conf file or using the ifsysctl(5) files, that allow per-interface setup.
Forwarding can be also enabled in the /etc/sysconfig/sysctl file using the IP_FORWARD and IPV6_FORWARD variables.
The proxy entries are added and deleted using the if-{up|down}.d/ndp-proxy script, every time after an involved interface has been set
up or down.
SYNTAX
The format of the ifndp-proxy file is:
<address> <address interface> <proxy interface list>
The format of the ifndp-proxy-<address interface> file is same to above, but allows also to omit the address interface by using a "-" as
placeholder inside of the file, because it is already available in the file name:
<address> <address interface | -> <proxy interface list>
Lines beginning with # and blank lines are ignored.
Each line defines to add a proxy NDP/ARP entry with the address of or behind address interface to all interfaces in the proxy interface
list.
EXAMPLES
Let's assume, your machine is connected via eth0 to a switch with the networks 2001:db8:abba::/64 and 192.168.100.1/24 and is using the IP
address 1 itself. You'd like to use the addresses 11 and 12 e.g. for virtual machines behind the tap1 and tap2 interface, that is:
2001:db8:abba::1/64 -- local eth0 address
2001:db8:abba::11/64 -- address behind tap1
2001:db8:abba::12/64 -- address behind tap2
192.168.100.1/24 -- local eth0 address
192.168.100.11/24 -- address behind tap1
192.168.100.12/24 -- address behind tap2
then set up the following entries in the ifndp-proxy file:
2001:db8:abba::1 eth0 tap1 tap2
2001:db8:abba::11 tap1 eth0 tap2
2001:db8:abba::12 tap2 eth0 tap1
192.168.100.1 eth0 tap1 tap2
192.168.100.11 tap1 eth0 tap2
192.168.100.12 tap2 eth0 tap1
additionally to the routing entries in the routes or ifroute-<interface name> files.
BUGS
Please report bugs at <https://bugzilla.novell.com/>
AUTHOR
Marius Tomaschewski <mt@suse.de>
SEE ALSO ifup(8)ifcfg(5)ifsysctl(8)sysconfig December 2009 IFNDP-PROXY(5)