Sponsored Content
Operating Systems Solaris Missing ASM Disks in Solaris 11.3 LDOM Post 303024995 by hicksd8 on Monday 22nd of October 2018 11:18:18 AM
Old 10-22-2018
Hmmmm.......this sounds weird. I haven't had much experience with ASM so I don't have a stock answer but perhaps just some pointers might help especially with someone as experienced as you.

Some of this you'll already know so apologies for that.

In my experience, maintenance mode is caused by unable to mount /usr. Of course, if the O/S couldn't access root (/) then it wouldn't boot at all but it also needs access to /usr to avoid calling maintenance mode. So where is your /usr? On what disk(s)?

Inability to access disk(s) can be caused by the device node (/dev/dsk, /dev/rdsk, /dev/cfg) files being missing so I would check them. Yes, to do that I would be using 'format' to tell me the correct device node(s) by discovering them.

ASM uses device maps in /devices I believe. Do they look right?

Does running 'format' in expert mode (-e) show you anything different???

Are the missing disks on a SAN? If so, have the storage boys made them visible to this box?

As you suggest, I would use 'devfsadm' to recreate the missing device nodes but, of course, for that to work, the disks must already be physically visible.

These are just my thoughts. I would guess that this issue is at the O/S level and not directly related to ASM.

Just my thoughts.

Last edited by hicksd8; 10-22-2018 at 12:58 PM..
 

9 More Discussions You Might Find Interesting

1. Solaris

Installing Solaris into LDom using DVD

Hi, I have issues installing Solaris into a LDom using a Solaris10u5/08 DVD. I have been troubleshooting for the past 2 days and I still cannot get it up. Here is the logs: root@eld-app2# ldm add-vdsdev /cdrom/sol_10_508_sparc/s0 cdrom0@primary-vds0 root@eld-app2# ldm add-vdisk cdrom0... (4 Replies)
Discussion started by: bolasutra
4 Replies

2. Solaris

How to find missing disks on Sun x4150 without reboot?

Hi, Here is the issue: There are 4 disks on this Sun x4150 system under Solaris 10, but only 1 disk can be seen by the OS. I've tried commands disks and devfsadm but not working. It's an important production server, so 'reboot -r' is not a choice. # format < /dev/null Searching for... (6 Replies)
Discussion started by: aixlover
6 Replies

3. Solaris

Solaris 10 Installation - Disks missing, and Raid

Hey everyone. First, let me start by saying I'm primarily focused on linux boxes, and just happened to get pulled into building two T5220's. I'm not super educated on sun boxes. Both T5220's have 8 146GB 15k SAS drives. Inside the service processor, I can run SHOW /SYS/HDD{0-7} and they all come... (2 Replies)
Discussion started by: msarro
2 Replies

4. Solaris

ZFS LDOM problem on Solaris 10

Apologies if this is the wrong forum.. I have some LDOMs running on a Sparc server. I copied the disk0 file from one chassis over to another, stopped the ldom on the source system and started it on the 2nd one. All fine. Shut it down and flipped back. We then did a fair bit of work on the... (4 Replies)
Discussion started by: tommyq
4 Replies

5. Solaris

Disks missing from /devices folder. Not sure why.

Help Please! I picked up a V440 and it has 4 disks. I installed Solaris fine to disk 3, but I cannot see the other disks in Solaris. I have run probe-scsi-all from OBP and I see the other disks and they have names in devalias AFAIK. It's just in Solaris they do not appear. I have run... (6 Replies)
Discussion started by: greg1975
6 Replies

6. Solaris

Virtual disks are not showing up in LDom

I have an Oracle VM set up with 1 virtual disk. I am trying to add 2 new disks to it. I was able to successfully add 1 (it appears when I run "format" in the VM) but when I add the second and third disks they do not appear in my VM. Here are the commands I ran: ldm add-vdsdev... (3 Replies)
Discussion started by: unblockable
3 Replies

7. Solaris

Virtual Switch in Solaris LDOM

Hi, Our existing environment is having primary domain and 3 guest domains are running over it. See the attached image. Now we want to add a new primary virtual switch and move LDOM3 to be connected with new primary switch. So, I am not sure how to achieve this because. If I remove the... (7 Replies)
Discussion started by: praveensharma21
7 Replies

8. Solaris

Oracle ASM on Solaris 11.3

Hi Folks, I've just built a Solaris 11.3 server with a number of LDOM's, all good and well and not any serious issues so far. On our older Solaris 10 systems we ran Oracle 11g using ASM disks, these disks were the raw device meta disks and came in very nicely as "/dev/md/rdsk/dnn" all worked... (4 Replies)
Discussion started by: gull04
4 Replies

9. Solaris

Solaris LDOM IP conflict

I have a Sun T4-1 running Solaris 11.4 with a static IP 192.168.0.183. On this machine is a Solaris 10 LDOM with a static IP of 192.168.0.78. The other day I had to stop the LDOM to do a memory reconfigure. When I rebooted it I got an error that the IP 192.168.0.78 was already in use and so... (4 Replies)
Discussion started by: Michele31416
4 Replies
disks(1M)						  System Administration Commands						 disks(1M)

NAME
disks - creates /dev entries for hard disks attached to the system SYNOPSIS
/usr/sbin/disks [-C] [-r rootdir] DESCRIPTION
devfsadm(1M) is now the preferred command for /dev and should be used instead of disks. disks creates symbolic links in the /dev/dsk and /dev/rdsk directories pointing to the actual disk device special files under the /devices directory tree. It performs the following steps: 1. disks searches the kernel device tree to see what hard disks are attached to the system. It notes the /devices pathnames for the slices on the drive and determines the physical component of the corresponding /dev/dsk or /dev/rdsk name. 2. The /dev/dsk and /dev/rdsk directories are checked for disk entries - that is, symbolic links with names of the form cN[tN]dNsN, or cN[tN]dNpN, where N represents a decimal number. cN is the logical controller number, an arbitrary number assigned by this program to designate a particular disk controller. The first controller found on the first occasion this program is run on a system, is assigned number 0. tN is the bus-address number of a subsidiary controller attached to a peripheral bus such as SCSI or IPI (the target number for SCSI, and the facility number for IPI controllers). dN is the number of the disk attached to the controller. sN is the slice number on the disk. pN is the FDISK partition number used by fdisk(1M). (x86 Only) 3. If only some of the disk entries are found in /dev/dsk for a disk that has been found under the /devices directory tree, disks creates the missing symbolic links. If none of the entries for a particular disk are found in /dev/dsk, disks checks to see if any entries exist for other disks attached to the same controller, and if so, creates new entries using the same controller number as used for other disks on the same controller. If no other /dev/dsk entries are found for slices of disks belonging to the same physical con- troller as the current disk, disks assigns the lowest-unused controller number and creates entries for the disk slices using this newly-assigned controller number. disks is run automatically each time a reconfiguration-boot is performed or when add_drv(1M) is executed. When invoking disks(1M) manually, first run drvconfig(1M) to ensure /devices is consistent with the current device configuration. Notice to Driver Writers disks considers all devices with a node type of DDI_NT_BLOCK, DDI_NT_BLOCK_CHAN, DDI_NT_CD, DDI_NT_BLOCK_WWN or DDI_NT_CD_CHAN to be disk devices. disks(1M) requires the minor name of disk devices obey the following format conventions. The minor name for block interfaces consists of a single lowercase ASCII character, a through u. The minor name for character (raw) inter- faces consists of a single lowercase ASCII character, a through u, followed by ,raw. disks translates a through p to s0 through s15, while it translates q through u to p0 through p4. SPARC drivers should only use the first 8 slices: a through h, while x86 drivers can use a through u, with q through u corresponding to fdisk(1M) partitions. q represents the entire disk, while r, s, t, and u represent up to 4 additional partitions. To prevent disks from attempting to automatically generate links for a device, drivers must specify a private node type and refrain from using a node type: DDI_NT_BLOCK, DDI_NT_BLOCK_CHAN, DDI_NT_CD, or DDI_NT_CD_CHAN when calling ddi_create_minor_node(9F). OPTIONS
The following options are supported: -C Causes disks to remove any invalid links after adding any new entries to /dev/dsk and /dev/rdsk. Invalid links are links which refer to non-existent disk nodes that have been removed, powered off, or are otherwise inaccessible. -r rootdir Causes disks to presume that the /dev/dsk, /dev/rdsk and /devices directory trees are found under rootdir, not directly under /. ERRORS
If disks finds entries of a particular logical controller linked to different physical controllers, it prints an error message and exits without making any changes to the /dev directory, since it cannot determine which of the two alternative logical-to-physical mappings is correct. The links should be manually corrected or removed before another reconfiguration-boot is performed. EXAMPLES
Example 1: Creating Block and Character Minor Devices The following example demonstrates creating the block and character minor devices from within the xkdisk driver's attach(9E) function. #include <sys/dkio.h> /* * Create the minor number by combining the instance number * with the slice number. */ #define MINOR_NUM(i, s) ((i) << 4 | (s)) int xkdiskattach(dev_info_t *dip, ddi_attach_cmd_t cmd) { int instance, slice; char name[8]; /* other stuff in attach... */ instance = ddi_get_instance(dip); for (slice = 0; slice < V_NUMPAR; slice++) { /* * create block device interface */ sprintf(name, "%c", slice + 'a'); ddi_create_minor_node(dip, name, S_IFBLK, MINOR_NUM(instance, slice), DDI_NT_BLOCK_CHAN, 0); /* * create the raw (character) device interface */ sprintf(name,"%c,raw", slice + 'a'); ddi_create_minor_node(dip, name, S_IFCHR, MINOR_NUM(instance, slice), DDI_NT_BLOCK_CHAN, 0); } } Installing the xkdisk disk driver on a Sun Fire 4800, with the driver controlling a SCSI disk (target 3 attached to an isp(7D) SCSI HBA) and performing a reconfiguration-boot (causing disks to be run) creates the following special files in /devices. # ls -l /devices/ssm@0,0/pci@18,700000/pci@1/SUNW,isptwo@4/ brw-r----- 1 root sys 32, 16 Aug 29 00:02 xkdisk@3,0:a crw-r----- 1 root sys 32, 16 Aug 29 00:02 xkdisk@3,0:a,raw brw-r----- 1 root sys 32, 17 Aug 29 00:02 xkdisk@3,0:b crw-r----- 1 root sys 32, 17 Aug 29 00:02 xkdisk@3,0:b,raw brw-r----- 1 root sys 32, 18 Aug 29 00:02 xkdisk@3,0:c crw-r----- 1 root sys 32, 18 Aug 29 00:02 xkdisk@3,0:c,raw brw-r----- 1 root sys 32, 19 Aug 29 00:02 xkdisk@3,0:d crw-r----- 1 root sys 32, 19 Aug 29 00:02 xkdisk@3,0:d,raw brw-r----- 1 root sys 32, 20 Aug 29 00:02 xkdisk@3,0:e crw-r----- 1 root sys 32, 20 Aug 29 00:02 xkdisk@3,0:e,raw brw-r----- 1 root sys 32, 21 Aug 29 00:02 xkdisk@3,0:f crw-r----- 1 root sys 32, 21 Aug 29 00:02 xkdisk@3,0:f,raw brw-r----- 1 root sys 32, 22 Aug 29 00:02 xkdisk@3,0:g crw-r----- 1 root sys 32, 22 Aug 29 00:02 xkdisk@3,0:g,raw brw-r----- 1 root sys 32, 23 Aug 29 00:02 xkdisk@3,0:h crw-r----- 1 root sys 32, 23 Aug 29 00:02 xkdisk@3,0:h,raw /dev/dsk will contain the disk entries to the block device nodes in /devices # ls -l /dev/dsk /dev/dsk/c0t3d0s0 -> ../../devices/[...]/xkdisk@3,0:a /dev/dsk/c0t3d0s1 -> ../../devices/[...]/xkdisk@3,0:b /dev/dsk/c0t3d0s2 -> ../../devices/[...]/xkdisk@3,0:c /dev/dsk/c0t3d0s3 -> ../../devices/[...]/xkdisk@3,0:d /dev/dsk/c0t3d0s4 -> ../../devices/[...]/xkdisk@3,0:e /dev/dsk/c0t3d0s5 -> ../../devices/[...]/xkdisk@3,0:f /dev/dsk/c0t3d0s6 -> ../../devices/[...]/xkdisk@3,0:g /dev/dsk/c0t3d0s7 -> ../../devices/[...]/xkdisk@3,0:h and /dev/rdsk will contain the disk entries for the character device nodes in /devices # ls -l /dev/rdsk /dev/rdsk/c0t3d0s0 -> ../../devices/[...]/xkdisk@3,0:a,raw /dev/rdsk/c0t3d0s1 -> ../../devices/[...]/xkdisk@3,0:b,raw /dev/rdsk/c0t3d0s2 -> ../../devices/[...]/xkdisk@3,0:c,raw /dev/rdsk/c0t3d0s3 -> ../../devices/[...]/xkdisk@3,0:d,raw /dev/rdsk/c0t3d0s4 -> ../../devices/[...]/xkdisk@3,0:e,raw /dev/rdsk/c0t3d0s5 -> ../../devices/[...]/xkdisk@3,0:f,raw /dev/rdsk/c0t3d0s6 -> ../../devices/[...]/xkdisk@3,0:g,raw /dev/rdsk/c0t3d0s7 -> ../../devices/[...]/xkdisk@3,0:h,raw FILES
/dev/dsk/* Disk entries (block device interface) /dev/rdsk/* Disk entries (character device interface) /devices/* Device special files (minor device nodes) ATTRIBUTES
See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ SEE ALSO
add_drv(1M), devfsadm(1M), fdisk(1M), attributes(5), isp(7D), devfs(7FS), dkio(7I), attach(9E), ddi_create_minor_node(9F) Writing Device Drivers BUGS
disks silently ignores malformed minor device names. SunOS 5.10 7 Nov 2002 disks(1M)
All times are GMT -4. The time now is 04:09 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy