10-10-2018
I have no experience with boot from SAN on metal, to put a small disclaimer upfront.
Not related to the problem...what would really help you is to have a separated installed operating system on both environments (DCs), with data part replicated in separate volume groups.
That way, only thing you do is import the volume group and (possibly or not depends) an ip assignment, depending on the topology and services such as vrrp or higher layer used.
I never endorsed SAN boot on metal personally (but in vms of course), always had couple of local disks to mirror ...
Point being, i would go with service separation and clean install on each of the sites, while cloning data part via storage methods.
Hopefully someone else who used linux SAN boot will be of more assistance with the actual problem.
Regards
Peasant.
This User Gave Thanks to Peasant For This Post:
10 More Discussions You Might Find Interesting
1. Solaris
I have solaris 10 sparc. I installed a Qlogic hba card.
This card is connected on a brocade switch and the brocade is connected on 2 different controllers on a Hitachi disk bay.
I formated 2 luns. On my solaris system, i have 4 disk.
How to configure solaris 10 to fix the dual disk view.
... (4 Replies)
Discussion started by: simquest
4 Replies
2. Solaris
Hi,
I saw your post on the forums about how to setup IP multipathing. I wanted your help on the below situation .
I have 2 servers A and B . Now they should be connected to 2 network switches . S1 and S2.
Now is it possible to have IP Multipathing on each of the servers as follows ?
... (0 Replies)
Discussion started by: maadhuu
0 Replies
3. Solaris
Hai
we using emc storage which is conneted to M5000 through san switch.
we asign 13 luns but in server it is showing 22 luns.
i enable the solaris multipathing (MPxIO)
#more /kernel/drv/fp.conf in that file
MPxio-disable=no
#mpathadm list lu
it shows ... (2 Replies)
Discussion started by: joshmani
2 Replies
4. Solaris
Hello,
I turned on the server multipathing:
# uname -a
SunOS caiman 5.10 Generic_141444-09 sun4v sparc SUNW,T5140
stmsboot -D fp -e
And after a reboot the server, multipathing is not enable:
# stmsboot -L
stmsboot: MPxIO is not enabled
stmsboot: MPxIO disabled
# ls /dev/dsk... (4 Replies)
Discussion started by: bieszczaders
4 Replies
5. UNIX for Dummies Questions & Answers
Hello,
I'm trying to put puppy linux 4.2.1 (I can't use the latest because it won't boot on my hardware) on a grub2'd usb drive.
It throws the error that it can't find pup_421.sfs
Here is my /boot/grub/grub.cfg
menuentry "Puppy 4.2.1" {
loopback loop... (2 Replies)
Discussion started by: Narnie
2 Replies
6. Debian
Hello, firstly excuse for my poor english.
I have a busybox error when I try to run Debian 6. It's like Grub cannot find root (initramfs)
My system is:
- RAID0 with dmraid
- /boot ext2 (from moonOS installation --ubuntu based--)
- ext4 (moonOS wich have the Grub2 installation, where I... (0 Replies)
Discussion started by: neutralTTY
0 Replies
7. Linux
I got a dual boot with grub2, but everytime I turn on the computer and the booter is loaded, I can't handle the menu, so I am forced to wait the countdown and choose the default option.
I'd really like to know why!
This is my grub.cfg,
# # DO NOT EDIT THIS FILE # # It is automatically... (0 Replies)
Discussion started by: Luke Bonham
0 Replies
8. Red Hat
Hello
This is happening on: 3.13.7-200.fc20.x86_64
This happened already some weeks ago, until now i didn install linunx onto this machine, as i had to turn in the laptop to the service center so they could fix the UEFI flash storage.
Either way, its happening again. as i installed Fedora 20... (1 Reply)
Discussion started by: sea
1 Replies
9. Red Hat
I have a couple of questions regarding multipath.
If I do vgdisplay vg01, I see it is using 1 PV: /dev/dm-13
If I type multipath -ll I see dm-9, dm-10, dm-11, dm-12, but do not see dm-13. Is my vg01 multipathed? How can I actually know for sure?
Secondly, let's say this time vg01 says... (1 Reply)
Discussion started by: keelba
1 Replies
10. UNIX for Beginners Questions & Answers
I have centos 7 gui installed on vmware workstation12 on my laptop.WhenI want to pause my splash screen while starting my centos 7 using the 'esc key' nothing happens and the system just boots up.I also see a entry for aci_memory_fail... entry during the boot process.help me fix the system. (1 Reply)
Discussion started by: sabsac
1 Replies
LEARN ABOUT HPUX
vxdestroy_lvmroot
vxdestroy_lvmroot(1M) vxdestroy_lvmroot(1M)
NAME
vxdestroy_lvmroot - remove LVM root disk and associated LVM volume group
SYNOPSIS
vxdestroy_lvmroot [-v] [-b] lvm_root_disk
DESCRIPTION
The vxdestroy_lvmroot command tears down and removes the LVM volume group associated with the specified physical disk. This is done by
removing the volumes in the volume group and then removing the volume group.
OPTIONS
-b Invokes the setboot command to change the primary boot disk to the VxVM root disk from which the system was booted (if the pri-
mary boot disk is not already set to this disk). The alternate boot device remains unchanged. If the -v option is also speci-
fied, the settings of the primary and alternate boot devices are displayed.
-v Outputs verbose messages including a timestamp that indicates major operations being performed.
ARGUMENTS
lvm_root_disk
Specifies the device name of the LVM root disk that is to be destroyed, along with its entire volume group.
EXAMPLES
This example shows the vxdestroy_lvmroot command invoked in its simpliest form:
/etc/vx/bin/vxdestroy_lvmroot c5t1d0
# /etc/vx/bin/vxdestroy_lvmroot -v -b c3t0d0
Are you sure about destroying c3t0d0 (imported on VG /dev/vg02) ? YES
vxdestroy_lvmroot 06:02: Tearing down /dev/vg02 on device c3t0d0
vxdestroy_lvmroot 06:02:
Unmounting and removing any volumes associated with /dev/vg02
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol1
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol2
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol3
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol4
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol5
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol6
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol7
vxdestroy_lvmroot 06:02: removing logical volume /dev/vg02/lvol8
vxdestroy_lvmroot 06:02: Removing Volume Group /dev/vg02
vxdestroy_lvmroot 06:02: Removing device files in /dev/vg02
vxdestroy_lvmroot 06:02: Removing LVM Physical Volume c3t0d0
vxdestroy_lvmroot 06:02: Removing LVM Physical Volume c1t1d3
vxdestroy_lvmroot 06:02: Removing LVM Physical Volume c1t1d4
vxdestroy_lvmroot 06:02: Removing LVM Physical Volume c1t1d5
vxdestroy_lvmroot 06:03: Current setboot values:
vxdestroy_lvmroot 06:03: Primary: 0/0/6/0/0.0.0
vxdestroy_lvmroot 06:03: Alternate: 0/0/1/0/0.1.0
vxdestroy_lvmroot 06:03:
Making disk c0t1d0 (0/0/1/0/0.1.0) the primary boot disk
vxdestroy_lvmroot 06:03:
Removal of device c3t0d0, volume group /dev/vg02 was successful
SEE ALSO
cpio(1), dd(1), fsck(1M), setboot(1M) vxbootsetup(1M) vxcp_lvmroot(1M) vxres_lvmroot(1M)
VxVM 5.0.31.1 24 Mar 2008 vxdestroy_lvmroot(1M)