10-09-2018
Configure Solaris zone on new network
Hi,
I have a Solaris 10 zone which I need to configure on a new network. I have configured the new IP on the zone itself and I can ping the interface from a node on the same network, but not from another network. Basically I need to know how to route the traffic from the zone to it's default gateway.
Example:
BGE0 - IP 192.168.1.1 - GW 192.168.1.254
BGE1 - IP 192.168.100.1 - GW 192.168.100.254
Zone IP: 192.168.100.2 - GW 192.168.100.254.
Default Gateway on the global zone is 192.168.1.254
I've looked up IPFilters and come up with the entry below. I'm just wondering would this entry work? I just want to be sure before enabling IPFilters and adding entries as I have a number of prod zones running on this global zone and don't want to break the networking.
pass out quick on bge0 to bge1:192.168.100.254 from 192.168.100.1 to any
Any help is greatly appreciated.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
Can anybody help me on how to configure the network in Sun Solaris. This is my first time to touch sun system please help!!!:confused: :confused: (2 Replies)
Discussion started by: jameswong
2 Replies
2. Solaris
I am seeking help from the gurus in this forum and hope that I can find answers soon. Anyone who provide the answers will be greatly appreciated.
I have a sparc box with Solaris 10 on it. We install Solaris with zone structure. One global zone and two other zone. I installed Oracle DB on global... (6 Replies)
Discussion started by: duke0001
6 Replies
3. Solaris
Hi..i have installed solaris 10 on vmware. I m not able connect to internet.
pls help in detail. how to solve the problem. During the installation i have put no DHCP. cofigured manually ( Ip 192.168.1.9) default gateway 192.168.1.1 . (3 Replies)
Discussion started by: johnavery
3 Replies
4. Solaris
Hi
i have created a solaris zone but have not yet connected any network cables for this new zone,
can i set the zone up without running the command 'add net' and not adding an ip or physical interface?
i tried to add dummy internet settings and get this
zonecfg:coddr> add net... (4 Replies)
Discussion started by: newbiesolaris10
4 Replies
5. Solaris
Hi, guys, recently my os changed to solaris 10, and i want to share the printer with another computer whose os is also solaris. Is there anyone could give me a hint to fix this problem.
lpadmin -p hp5200 -v /dev/null -A write -n... (1 Reply)
Discussion started by: papertiger
1 Replies
6. Solaris
Hi,
I have installed Solaris 10 on VMware7, When i used ifconfig -a to check network interface, it has shown lo0 as loopback interface.
Please advise how to configure network interfaces using VMware. (1 Reply)
Discussion started by: ajhal04
1 Replies
7. Solaris
I am trying to create a branded 10 zone on a Solaris 11.1 control domain. I am using a flar image (cpio) from an existing LDOM. Here are the steps taken after flarcreate.
#zonecfg -z <device>
>create -b
>set brand=solaris10
>set zonepath=/zonez/<device>
>set ip-type=exclusive
>add net... (1 Reply)
Discussion started by: aeroforce
1 Replies
8. Solaris
Hello, I followed these instructions to create a Solaris 11 zone:
http://www.oracle.com/technetwork/articles/servers-storage-admin/o11-092-s11-zones-intro-524494.html
And I am unable to ping anything from the Local Zone except for the IP address of the global zone.
My global zone has an IP... (6 Replies)
Discussion started by: unblockable
6 Replies
9. Solaris
Have 2 nics on physical system
net0 phys 1500 up --
net1 phys 1500 up --
1. I want to create a link aggregation with LACP enabled with above 2 nics
2. Create port-group(Like we create on ESXi) with VLAN-ID 2141
3. And assign this... (0 Replies)
Discussion started by: Shirishlnx
0 Replies
10. Solaris
Hi, hoping someone can help, its been a while since I used Solaris.
After creating a NGZ (non global zone), the NGZ can access the GZ (Global Zone) and the GZ can access the NGZ (using ssh, zlogin)
However, the NGZ cannot access any other netwqork devices, it can't even see the default router
... (2 Replies)
Discussion started by: GazinLincoln
2 Replies
LEARN ABOUT DEBIAN
atalkd
ATALKD(8) Netatalk 2.2 ATALKD(8)
NAME
atalkd - AppleTalk RTMP, NBP, ZIP, and AEP manager
SYNOPSIS
atalkd [-f configfile] [-1] [-2]
DESCRIPTION
atalkd is responsible for all user level AppleTalk network management. This includes routing, name registration and lookup, zone lookup,
and the AppleTalk Echo Protocol (similar to ping(8)). atalkd is typically started at boot time, out of /etc/rc. It first reads from its
configuration file, /etc/netatalk/atalkd.conf. If there is no configuration file, atalkd will attempt to configure all available interfaces
and will create a configuration file. The file consists of a series of interfaces, one per line. Lines with `#' in the first column are
ignored, as are blank lines. The syntax is
interface [ -seed ] [ -phase number ] [ -net net-range ] [ -addr address ] [ -zone zonename ] ...
Note that all fields except the interface are optional. The loopback interface is configured automatically. If -seed is specified, all
other fields must be present. Also, atalkd will exit during bootstrapping, if a router disagrees with its seed information. If -seed is not
given, all other information may be overriden during auto-configuration. If no -phase option is given, the default phase as given on the
command line is used (the default is 2). If -addr is given and -net is not, a net-range of one is assumed.
The first -zone directive for each interface is the ``default'' zone. Under Phase 1, there is only one zone. Under Phase 2, all routers on
the network are configured with the default zone and must agree. atalkd maps ``*'' to the default zone of the first interface. Note: The
default zone for a machine is determined by the configuration of the local routers; to appear in a non-default zone, each service, e.g.
afpd, must individually specify the desired zone. See also nbp_name(3).
ROUTING
If you are connecting a netatalk router to an existing AppleTalk internet, you should first contact your local network administrators to
obtain appropriate network addresses.
atalkd can provide routing between interfaces by configuring multiple interfaces. Each interface must be assigned a unique net-range
between 1 and 65279 (0 and 65535 are illegal, and addresses between 65280 and 65534 are reserved for startup). It is best to choose the
smallest useful net-range, i.e. if you have three machines on an Ethernet, don't chose a net-range of 1000-2000. Each net-range may have an
arbitrary list of zones associated with it.
EXAMPLES
Below is an example configuration file for a sun4/40. The machine has two interfaces, ``le0'' and ``le1''. The ``le0'' interface is
configured automatically from other routers on the network. The machine is the only router for the ``le1'' interface.
le0
le1 -seed -net 9461-9471 -zone netatalk -zone Argus
atalkd automatically acts as a router if there is more than one interface.
FILES
/etc/netatalk/atalkd.conf configuration file
BUGS
On some systems, atalkd can not be restarted.
SEE ALSO
atalkd.conf(5)
Netatalk 2.2 06 Sep 2004 ATALKD(8)