I'm fairly new to hpux, so this is what i've been trying to figure out. Is it possible to get any logs on hpux that would indicate if the system, cpu, or other hardware components reached above normal or critical temperatures?
Thanks,
-K (0 Replies)
Is there command in sco unixware 7.1.3 from which i can find the temperature of the system/hardware.
Something equivalent to prtdiag in solaris maybe
thanks (1 Reply)
Hi all
I have a SUN V480 server with 4 processores and I've noticed that the temperature for 2 of the 4 processers are quite high (63 degrees Celsius).
Does anyone know what the operating temperatures of the Sparc CPU's are? I'm not getting any warning messages yet, but I want to resolve the... (3 Replies)
Hi,
I just set up a raid Z array in solaris xpress and I notice that the drives feel pretty damn hot. I use speedfan to monitor the temperatures of the hard drives in XP. Is there a similar program for solrais? I assume there would be since the drives all have temp sensors in them, but I... (2 Replies)
This is the code:
while test 1 -eq 1
do
read a
$a
if test $a = stop
then
break
fi
done
I read a command on every loop an execute it.
I check if the string equals the word stop to end the loop,but it say that I gave too many arguments to test.
For example echo hello.
Now the... (1 Reply)
How to get a CPU temperature and current power consumption in T5220 server both from system controller and Operating system. I need details by cores. Thanks in advance. (13 Replies)
People hello to everybody exist a way to do a script for view the temperature. I have
Red Hat Linux release 9 (Shrike)
Kernel 2.4.20-8 on an i686
THANk YOU FOR YOUR TIME. (4 Replies)
some say '/usr/sfw/bin/ipmitool' can be used to read temperature. has anyone tried it? what options should be used? (1 Reply)
Discussion started by: orange47
1 Replies
LEARN ABOUT DEBIAN
eatmydata
eatmydata(1) General Commands Manual eatmydata(1)NAME
eatmydata - transparently disable fsync() and other data-to-disk synchronization calls
SYNOPSIS
eatmydata [--] command [ command arguments ... ]
DESCRIPTION
eatmydata runs a command in the environment where data-to-disk synchronization calls (like fsync(), fdatasync(), sync(), msync() and open()
O_SYNC / O_DSYNC flags) have no effect. LD_PRELOAD library libeatmydata overrides respective C library calls with custom functions that
don't trigger synchronization but return success nevertheless.
You may use eatmydata in two ways. In normal mode, just execute eatmydata directly and pass a command-to-be-run and its arguments via com-
mand line. In order to use symlink mode, create a symlink to /usr/bin/eatmydata with the filename (a.k.a basename) of another program in
the PATH and execute eatmydata via that symlink. Then eatmydata will find that program in the PATH and run it in the libeatmydata environ-
ment repassing all command line options.
OPTIONS
Please note that eatmydata does not process any command line options in symlink mode. All command line options will be repassed to the
underlying executable as-is.
command
The command to execute. It may be either a full path or the name of the command in PATH. In case command cannot be found in PATH,
eatmydata will fail.
command arguments
Arbitrary number of arguments to pass to the command being executed.
-- Optional command separator for compatibility with similar utilities. Ignored at the moment.
EXAMPLES
Given PATH is /usr/bin and both /usr/bin/aptitude and /usr/bin/eatmydata are installed, the following:
$ ln -s /usr/bin/eatmydata ./aptitude
$ ./aptitude moo
is equivalent to:
$ eatmydata -- aptitude moo
Therefore, you may use symlink mode to automatically run specific programs in the libeatmydata environment whenever you run them from PATH.
For example, given standard PATH settings, just do:
# ln -s /usr/bin/eatmydata /usr/local/bin/aptitude
and enjoy sync-free aptitude system-wide.
AUTHOR
The eatmydata wrapper around libeatmydata LD_PRELOAD library was written by Modestas Vainius <modax@debian.org>
November 2010 eatmydata(1)