10-08-2018
Quote:
Originally Posted by
Marika
Advice?
At the danger of disappointing you: not yet. This looks like an
interesting problem (in other words: you did nothing obvious wrong but it still doesn't work, so some culprit must exist but we don't know what it is) and it is time for serious debugging,
First, i googled the problem too and everywhere shared memory was mentioned. Have you had a look at the shared memory segments? You can do that with the
ipcs command. See the man page for details. If a process crashes it happens that shared memory segments allocated by that process remain allocated but are in fact unusable. In such a case you need to manually remove them (otherwise your memory is made smaller effectively) or reboot, which also gets rid of them.
I also found
this link which seems to be quite similar to your problem. Did you increase shared memory in the way the guy suggested? I also found
this link effectively saying the same thing.
Another thing i remembered: Oracle has 2 settings: SGA_TARGET and SGA_MAXSIZE. You need to set both of them.
I hope this helps.
bakunin
9 More Discussions You Might Find Interesting
1. Ubuntu
i trying to install hula onto my ubuntu but it seems to be not working. i follow through every instructions which i found from the net but is still not working. As i have already install allthe necessary dependency!
Below are all the dependency i have install:
debhelper (>= 4.0.0),... (0 Replies)
Discussion started by: thms_sum
0 Replies
2. Windows & DOS: Issues & Discussions
Hi ,
I hav a laptop with Vista, i need to install Ubuntu along with vista on it. But the problem is tht i donot hav a hard drive partition. though i have abt 70 gb of free space. the only other partition is "recovery" one, so i cnt play with it
how shld i perform the installation ?? (4 Replies)
Discussion started by: akshay61286
4 Replies
3. Ubuntu
Hi All
As i m trying to install ubuntu on my virtual PC where h/w confg is as 5GB didk n 512 mb RAm.
after selecting mode option, and after pressing F6 after that screen shows some msg. And not goes to next step.
What is the problem n wht i shall do??
Please provide me solution (3 Replies)
Discussion started by: sunray
3 Replies
4. Ubuntu
Hi all,
I have Windows XP dual boot with Ubuntu 8.10 on my system. I brought in a portable HDD on which I installed Ubuntu 10.04 32-bit. The grub boot loader was installed along with this and to boot windows, I've had to plug in the HDD (with lucid install) everytime. It had been working fine.... (0 Replies)
Discussion started by: morningSunshine
0 Replies
5. Ubuntu
Hi all- I'm getting ready to install Ubuntu onto my Sony Vaio laptop and had a few questions for which I have not yet found the answer.
1)Should I partition my hdd myself (including a swap partition) in Windows or should I do this when installing Ubuntu? When I do partition, since I have over... (2 Replies)
Discussion started by: Gatsby
2 Replies
6. Ubuntu
I wish to install the latest ubuntu on my desktop. How do I go about doing this ?
Also how do I create the superuser or admin once the installation is done ? (3 Replies)
Discussion started by: sundaresh
3 Replies
7. Solaris
System Model and Spec
Sun Enterprise 420R
Processor Speed: 450 MHz (4 processors)
Installed RAM: 4 GB
Os: Solaris 8 Sparc
I successfully installed standard oracle 8i setup on our database server specs above but after installation was competed and it went to creating database I got the... (2 Replies)
Discussion started by: Wpgn
2 Replies
8. Ubuntu
I've done a whole days work of researching how to install a program on ubuntu.. so first I downloaded python.. unpackaged it from .tar.xz now its just python-3.4.2 then I navigated to the dir in terminal.. then ran the ./configure make make test sudo make install commands which took like 10 minutes... (2 Replies)
Discussion started by: Marniwild
2 Replies
9. Shell Programming and Scripting
Hello everyone,
I've got some problem intalling a perl module.
The installation is well done as you can see below.
gueg@ux31:~$ sudo apt-get install libwww-mechanize-perl
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances
Lecture des informations d'état...... (4 Replies)
Discussion started by: tot94
4 Replies
IPCS(1) BSD General Commands Manual IPCS(1)
NAME
ipcs -- report System V interprocess communication facilities status
SYNOPSIS
ipcs [-abcMmopQqSsTt]
DESCRIPTION
The ipcs utility provides information on System V interprocess communication (IPC) facilities on the system.
The options are as follows:
-a Show the maximum amount of information possible when displaying active semaphores, message queues, and shared memory segments. (This
is shorthand for specifying the -b, -c, -o, -p, and -t options.)
-b Show the maximum allowed sizes for active semaphores, message queues, and shared memory segments. The ``maximum allowed size'' is
the maximum number of bytes in a message on a message queue, the size of a shared memory segment, or the number of semaphores in a
set of semaphores.
-c Show the creator's name and group for active semaphores, message queues, and shared memory segments.
-M Display system information about shared memory.
-m Display information about active shared memory segments.
-o Show outstanding usage for active message queues, and shared memory segments. The ``outstanding usage'' is the number of messages in
a message queue, or the number of processes attached to a shared memory segment.
-p Show the process ID information for active semaphores, message queues, and shared memory segments. The ``process ID information'' is
the last process to send a message to or receive a message from a message queue, the process that created a semaphore, or the last
process to attach or detach a shared memory segment.
-Q Display system information about messages queues.
-q Display information about active message queues.
-S Display system information about semaphores.
-s Display information about active semaphores.
-T Display system information about shared memory, message queues and semaphores.
-t Show access times for active semaphores, message queues, and shared memory segments. The access times is the time of the last con-
trol operation on an IPC object, the last send or receive of a message, the last attach or detach of a shared memory segment, or the
last operation on a semaphore.
If none of the -M, -m, -Q, -q, -S, or -s options are specified, information about all active IPC facilities is listed.
RESTRICTIONS
System data structures may change while ipcs is running; the output of ipcs is not guaranteed to be consistent.
BUGS
This manual page is woefully incomplete, because it does not at all attempt to explain the information printed by ipcs.
SEE ALSO
ipcrm(1)
AUTHORS
Thorsten Lockert <tholo@sigmasoft.com>
BSD
June 18, 1994 BSD