10-02-2018
There are no error messages to examine. Every command is run with "OK" exit status, but the config created by the commands is not correct. Clearly the problem is that I am doing it the wrong way and I wanted to get some advices on the correct way.
I would like to make NIM use install interface "if2" but it is still usind "if1", thus configuring bootptab with incorrect server address.
--Trifo
9 More Discussions You Might Find Interesting
1. AIX
HI folks,
Actually i have a network engineer having 2 and 1/2 years of experience in cisco having CCNA certification also. Now my company offering me to move to AIX field. I am new to AIX and do not know more about that field. So i want a suggestion from you peoples, that I have to join AIX or... (5 Replies)
Discussion started by: rawatmohinder
5 Replies
2. AIX
I try to migrate a NIM server from one server to another.
I try to do a mksysb on NIM server
restore the NIM server's mksysb to a client through NIM installation
shutdown NIM server
start newly installed client as NIM server
Does anyone do this before? who can give me some suggestion? (1 Reply)
Discussion started by: yanzhang
1 Replies
3. AIX
Hello everyone
Im trying to backup a nim client from nim master but I got this message
COMMAND STATUS
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
0042-001 nim:... (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
4. What is on Your Mind?
I've read about BITNET, CompuServe... CompuServe was probably not a network but an online service. Are (were) there any other networks alternative to Internet? Does anyone have experience with them? Do they still exist, is it possible to access them over Internet? There seems not to be another way... (13 Replies)
Discussion started by: Action
13 Replies
5. Solaris
If I have 2 interfaces in a server on the same subnet/network does Solaris automatically choose to route packets destined for this network out the first interface. I.e if ce0 and ce1 were on same network ce0 would be chosen as it's first interface? (5 Replies)
Discussion started by: Actuator
5 Replies
6. Solaris
ce0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 2
inet 10.162.212.132 netmask ffffff00 broadcast 10.162.212.255
ether 0:14:4f:55:82:9
ce1: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 3
inet 10.231.11.232 netmask... (3 Replies)
Discussion started by: busyboy
3 Replies
7. AIX
Hi.
I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ?
Tks (2 Replies)
Discussion started by: stephnane
2 Replies
8. AIX
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies
9. AIX
Friend's,
I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client?
All leads to the answer would be much appreciated, many thanks!
-- Souvik (2 Replies)
Discussion started by: thisissouvik
2 Replies
smart(8) smart(8)
NAME
smart - The Smart Package Manager
SYNOPSIS
smart command [options] [arguments]
DESCRIPTION
The Smart Package Manager project has the ambitious objective of creating smart and portable algorithms for solving adequately the problem
of managing software upgrading and installation. This tool works in all major distributions, and will bring notable advantages over native
tools currently in use (APT, APT-RPM, YUM, URPMI, etc).
Action commands
update
install
reinstall
upgrade
remove
check
fix
download
clean
Setup commands
channel
priority
mirror
flag
Query commands
search
query
info
stats
Run "smart command --help" for more information.
Options
--version
Show program's version number and exit
--config-file=FILE
Configuration file (default is <data-dir>/config)
--data-dir=DIR
Specifies the config file location - can take http, ftp urls and local file Data directory (default is /var/lib/smart/)
--log-level=LEVEL
Set the log level to level (debug, info, warning, error)
--gui Use the default graphic interface
--shell
Use the default shell interface
--interface=NAME
Use the given interface
--ignore-locks
Don't respect locking
-o OPT, --option=OPT
Set the option given by a name=value pair
Examples
smart install --help
smart install pkgname
smart --gui
smart --gui install pkgname
smart --shell
FILES
/etc/smart/
/var/lib/smart/
/usr/lib/smart/
/usr/lib/smart/plugins/
SEE ALSO
http://labix.org/smart
AUTHOR
Gustavo Niemeyer <gustavo@niemeyer.net>
Christoph Thiel 2006 Jun 16 smart(8)