10-02-2018
There are no error messages to examine. Every command is run with "OK" exit status, but the config created by the commands is not correct. Clearly the problem is that I am doing it the wrong way and I wanted to get some advices on the correct way.
I would like to make NIM use install interface "if2" but it is still usind "if1", thus configuring bootptab with incorrect server address.
--Trifo
9 More Discussions You Might Find Interesting
1. AIX
HI folks,
Actually i have a network engineer having 2 and 1/2 years of experience in cisco having CCNA certification also. Now my company offering me to move to AIX field. I am new to AIX and do not know more about that field. So i want a suggestion from you peoples, that I have to join AIX or... (5 Replies)
Discussion started by: rawatmohinder
5 Replies
2. AIX
I try to migrate a NIM server from one server to another.
I try to do a mksysb on NIM server
restore the NIM server's mksysb to a client through NIM installation
shutdown NIM server
start newly installed client as NIM server
Does anyone do this before? who can give me some suggestion? (1 Reply)
Discussion started by: yanzhang
1 Replies
3. AIX
Hello everyone
Im trying to backup a nim client from nim master but I got this message
COMMAND STATUS
Command: failed stdout: yes stderr: no
Before command completion, additional instructions may appear below.
0042-001 nim:... (2 Replies)
Discussion started by: lo-lp-kl
2 Replies
4. What is on Your Mind?
I've read about BITNET, CompuServe... CompuServe was probably not a network but an online service. Are (were) there any other networks alternative to Internet? Does anyone have experience with them? Do they still exist, is it possible to access them over Internet? There seems not to be another way... (13 Replies)
Discussion started by: Action
13 Replies
5. Solaris
If I have 2 interfaces in a server on the same subnet/network does Solaris automatically choose to route packets destined for this network out the first interface. I.e if ce0 and ce1 were on same network ce0 would be chosen as it's first interface? (5 Replies)
Discussion started by: Actuator
5 Replies
6. Solaris
ce0: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 2
inet 10.162.212.132 netmask ffffff00 broadcast 10.162.212.255
ether 0:14:4f:55:82:9
ce1: flags=1100843<UP,BROADCAST,RUNNING,MULTICAST,ROUTER,IPv4> mtu 1500 index 3
inet 10.231.11.232 netmask... (3 Replies)
Discussion started by: busyboy
3 Replies
7. AIX
Hi.
I change my client's IP and hostname but I forgot to change anything on the master. How can I redefine or modify my client's resource from my master, or with using smit niminit from my client ?
Tks (2 Replies)
Discussion started by: stephnane
2 Replies
8. AIX
Hello, I have an AIX6.1 machine which is a nim client to my nim master which is also AIX6.1 machine. I had some problem to perform an installation on my client using smit nim . i removed /etc/niminfo file in order to do the initialization again but when i run the command niminit -a name=client... (0 Replies)
Discussion started by: omonoiatis9
0 Replies
9. AIX
Friend's,
I was playing around with NIM in my environment & had a quick question in mind which I didn't/couldn't find answer to, which is -- how to find the name of the NIM server sitting on the NIM client?
All leads to the answer would be much appreciated, many thanks!
-- Souvik (2 Replies)
Discussion started by: thisissouvik
2 Replies
nohup(1) General Commands Manual nohup(1)
NAME
nohup - run a command immune to hangups
SYNOPSIS
command [arguments]
DESCRIPTION
executes command with hangups and quits ignored. If output is not redirected by the user, both standard output and standard error are sent
to If is not writable in the current directory, output is redirected to otherwise, fails. If a file is created, the file's permission bits
will be set to
If output from is redirected to a terminal, or is not redirected at all, the output is sent to
EXTERNAL INFLUENCES
Environment Variables
determines the language in which messages are displayed.
If is not specified in the environment or is set to the empty string, the value of is used as a default for each unspecified or empty vari-
able. If is not specified or is set to the empty string, a default of "C" (see lang(5)) is used instead of
If any internationalization variable contains an invalid setting, behaves as if all internationalization variables are set to "C". See
environ(5).
International Code Set Support
Single- and multi-byte character code sets are supported.
EXAMPLES
It is frequently desirable to apply to pipelines or lists of commands. This can be done only by placing pipelines and command lists in a
single file, called a shell script. To run the script using
features apply to the entire contents of file. If the shell script file is to be executed often, the need to type can be eliminated by
setting execute permission on file. The script can also be run in the background with interrupts ignored (see sh(1)):
file typically contains normal keyboard command sequences that one would want to continue running in case the terminal disconnects, such
as:
WARNINGS
Be careful to place punctuation properly. For example, in the command form:
applies only to command1. To correct the problem, use the command form:
Be careful of where standard error is redirected. The following command may put error messages on tape, making it unreadable:
whereas
puts the error messages into file
EXIT STATUS
The following exit values are returned:
The command specified by
command was found but could not be invoked
An error occurred in the nohup utility or the specified
command could not be found
Otherwise, the exit status of nohup will be that of the command specified.
SEE ALSO
chmod(1), nice(1), sh(1), signal(5).
STANDARDS CONFORMANCE
nohup(1)