Sponsored Content
Top Forums UNIX for Beginners Questions & Answers Shmem problem installing Oracle 12 C on Ubuntu 18.04 Post 303024118 by Marika on Sunday 30th of September 2018 02:01:03 PM
Old 09-30-2018
Yes, DISM.

MemTotal: 16342812 kB
SwapTotal: 8000508 kB

During installation I tried various configurations, with respectively 60, 40 and 25% of RAM value for total memory, of these % 3/4 was SGA, 1/4 PGA. So for example at 60% (10 GB) it was 7,5GB SGA + 2,5GB PGA. At one point I tried to go < 1 GB total.

So you are saying I must up the SGA value to mach (or exceed) swap?
 

9 More Discussions You Might Find Interesting

1. Ubuntu

installing hula on ubuntu

i trying to install hula onto my ubuntu but it seems to be not working. i follow through every instructions which i found from the net but is still not working. As i have already install allthe necessary dependency! Below are all the dependency i have install: debhelper (>= 4.0.0),... (0 Replies)
Discussion started by: thms_sum
0 Replies

2. Windows & DOS: Issues & Discussions

Installing Ubuntu in the same partition as Vista

Hi , I hav a laptop with Vista, i need to install Ubuntu along with vista on it. But the problem is tht i donot hav a hard drive partition. though i have abt 70 gb of free space. the only other partition is "recovery" one, so i cnt play with it how shld i perform the installation ?? (4 Replies)
Discussion started by: akshay61286
4 Replies

3. Ubuntu

Installation issue while installing ubuntu

Hi All As i m trying to install ubuntu on my virtual PC where h/w confg is as 5GB didk n 512 mb RAm. after selecting mode option, and after pressing F6 after that screen shows some msg. And not goes to next step. What is the problem n wht i shall do?? Please provide me solution (3 Replies)
Discussion started by: sunray
3 Replies

4. Ubuntu

Grub rescue problem after installing ubuntu 10.04 amd64 after i386

Hi all, I have Windows XP dual boot with Ubuntu 8.10 on my system. I brought in a portable HDD on which I installed Ubuntu 10.04 32-bit. The grub boot loader was installed along with this and to boot windows, I've had to plug in the HDD (with lucid install) everytime. It had been working fine.... (0 Replies)
Discussion started by: morningSunshine
0 Replies

5. Ubuntu

Installing Ubuntu

Hi all- I'm getting ready to install Ubuntu onto my Sony Vaio laptop and had a few questions for which I have not yet found the answer. 1)Should I partition my hdd myself (including a swap partition) in Windows or should I do this when installing Ubuntu? When I do partition, since I have over... (2 Replies)
Discussion started by: Gatsby
2 Replies

6. Ubuntu

Installing latest Ubuntu on my desktop

I wish to install the latest ubuntu on my desktop. How do I go about doing this ? Also how do I create the superuser or admin once the installation is done ? (3 Replies)
Discussion started by: sundaresh
3 Replies

7. Solaris

Problem Installing Oracle 8i

System Model and Spec Sun Enterprise 420R Processor Speed: 450 MHz (4 processors) Installed RAM: 4 GB Os: Solaris 8 Sparc I successfully installed standard oracle 8i setup on our database server specs above but after installation was competed and it went to creating database I got the... (2 Replies)
Discussion started by: Wpgn
2 Replies

8. Ubuntu

Downloading and installing (new to Ubuntu OS)

I've done a whole days work of researching how to install a program on ubuntu.. so first I downloaded python.. unpackaged it from .tar.xz now its just python-3.4.2 then I navigated to the dir in terminal.. then ran the ./configure make make test sudo make install commands which took like 10 minutes... (2 Replies)
Discussion started by: Marniwild
2 Replies

9. Shell Programming and Scripting

[Ubuntu / PERL ]Problem installing WWW::Mechanize mod

Hello everyone, I've got some problem intalling a perl module. The installation is well done as you can see below. gueg@ux31:~$ sudo apt-get install libwww-mechanize-perl Lecture des listes de paquets... Fait Construction de l'arbre des dépendances Lecture des informations d'état...... (4 Replies)
Discussion started by: tot94
4 Replies
sg_get_mem_stats(3)					     Library Functions Manual					       sg_get_mem_stats(3)

NAME
sg_get_mem_stats, sg_get_swap_stats - get VM statistics SYNOPSIS
#include <statgrab.h> sg_mem_stats *sg_get_mem_stats(void); sg_swap_stats *sg_get_swap_stats(void); DESCRIPTION
Memory statistics are accessed through the sg_get_mem_stats function. It returns a pointer to a static sg_mem_stats. The sg_get_swap_stats returns returns swap statistics. It returns a pointer to a static sg_swap_stats. On the FreeBSD operating system elevated privileges are required to access the swap statistics. Making the program setgid kmem should be sufficient. Programs running as root will not have this problem. RETURN VALUES
The VM system calls can return a pointer to either a sg_mem_stats or a sg_swap_stats. typedef struct{ long long total; long long free; long long used; long long cache; }sg_mem_stats; total The total amount of memory in bytes. free The total free memory in bytes. used The total used memory in bytes. cache The amount of cache used in bytes. typedef struct{ long long total; long long used; long long free; }sg_swap_stats; total The total swap space in bytes. used The used swap in bytes. free The free swap in bytes. TODO
Add a function to hold open the file descriptor to the kernel memory structures. Doing this would allow the elevated privileges to be dropped early on. SEE ALSO
statgrab(3) WEBSITE
http://www.i-scream.org/libstatgrab/ i-scream $Date: 2005/04/25 11:25:45 $ sg_get_mem_stats(3)
All times are GMT -4. The time now is 09:49 AM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy