09-30-2018
Did you check to make sure you had enough disk space?
9 More Discussions You Might Find Interesting
1. Ubuntu
i trying to install hula onto my ubuntu but it seems to be not working. i follow through every instructions which i found from the net but is still not working. As i have already install allthe necessary dependency!
Below are all the dependency i have install:
debhelper (>= 4.0.0),... (0 Replies)
Discussion started by: thms_sum
0 Replies
2. Windows & DOS: Issues & Discussions
Hi ,
I hav a laptop with Vista, i need to install Ubuntu along with vista on it. But the problem is tht i donot hav a hard drive partition. though i have abt 70 gb of free space. the only other partition is "recovery" one, so i cnt play with it
how shld i perform the installation ?? (4 Replies)
Discussion started by: akshay61286
4 Replies
3. Ubuntu
Hi All
As i m trying to install ubuntu on my virtual PC where h/w confg is as 5GB didk n 512 mb RAm.
after selecting mode option, and after pressing F6 after that screen shows some msg. And not goes to next step.
What is the problem n wht i shall do??
Please provide me solution (3 Replies)
Discussion started by: sunray
3 Replies
4. Ubuntu
Hi all,
I have Windows XP dual boot with Ubuntu 8.10 on my system. I brought in a portable HDD on which I installed Ubuntu 10.04 32-bit. The grub boot loader was installed along with this and to boot windows, I've had to plug in the HDD (with lucid install) everytime. It had been working fine.... (0 Replies)
Discussion started by: morningSunshine
0 Replies
5. Ubuntu
Hi all- I'm getting ready to install Ubuntu onto my Sony Vaio laptop and had a few questions for which I have not yet found the answer.
1)Should I partition my hdd myself (including a swap partition) in Windows or should I do this when installing Ubuntu? When I do partition, since I have over... (2 Replies)
Discussion started by: Gatsby
2 Replies
6. Ubuntu
I wish to install the latest ubuntu on my desktop. How do I go about doing this ?
Also how do I create the superuser or admin once the installation is done ? (3 Replies)
Discussion started by: sundaresh
3 Replies
7. Solaris
System Model and Spec
Sun Enterprise 420R
Processor Speed: 450 MHz (4 processors)
Installed RAM: 4 GB
Os: Solaris 8 Sparc
I successfully installed standard oracle 8i setup on our database server specs above but after installation was competed and it went to creating database I got the... (2 Replies)
Discussion started by: Wpgn
2 Replies
8. Ubuntu
I've done a whole days work of researching how to install a program on ubuntu.. so first I downloaded python.. unpackaged it from .tar.xz now its just python-3.4.2 then I navigated to the dir in terminal.. then ran the ./configure make make test sudo make install commands which took like 10 minutes... (2 Replies)
Discussion started by: Marniwild
2 Replies
9. Shell Programming and Scripting
Hello everyone,
I've got some problem intalling a perl module.
The installation is well done as you can see below.
gueg@ux31:~$ sudo apt-get install libwww-mechanize-perl
Lecture des listes de paquets... Fait
Construction de l'arbre des dépendances
Lecture des informations d'état...... (4 Replies)
Discussion started by: tot94
4 Replies
LEARN ABOUT OSF1
extendfs
extendfs(8) System Manager's Manual extendfs(8)
NAME
extendfs - Extends UFS file systems
SYNOPSIS
/sbin/extendfs [- s] [disk_blocks] device_name
DESCRIPTION
Use the extendfs command to increase the storage space in a UFS file system. The file system must not be mounted when you perform this
operation. To extend a mounted (in use) UFS file system, use the mount command with the -o extend option.
The procedure for increasing the storage space of a UFS file system is as follows: Look at the contents the /etc/fstab file to identify the
disk partition that maps to the file system. Ensure that there is available storage space on the target disk as follows: If LSM is in use
on your system, use LSM commands to increase the size of the LSM volume as described in the Logical Storage Manager guide. If LSM is not
in use on your system, use the disklabel command or the diskconfig graphical user interface to check the current size and use of partitions
on the disk. If there is adequate space on an adjacent partition, use the disklabel command to write the current label to a file as fol-
lows: # disklabel -r dsk4 > d4label Edit the disklabel file to change the size of the partition on which your UFS file system resides.
Increase the number of disk blocks on the partition and decrease the disk block size of the adjacent partition by an equivalent number.
Use the disklabel command with the -R option to write the revised label to the raw disk as follows: # disklabel -R /dev/rdisk/dsk4 d4label
When the disk label is revised, extend the file system using the extendfs command. You can either use the full extent of the newly sized
partition or extend the file system in stages. The following example commands show both methods. To extend the file system to use all the
available space, you specify the disk partition on which the file system resides, as follows: # extendfs /dev/disk/dsk4g To extend the
file system to use only part of the available space, you specify a number of disk blocks, as follows: # extendfs -s 300000 /dev/disk/dsk4g
The remainder of the extended partion is reserved for future use.
You can extend a file system as many times as necessary, up to the physical limit of the storage device. When no more space is available
on the storage device, you must back up the file system using the dump command and restore the file system to a storage device that has
more available space.
Once you have extended a file system, the operation cannot be reversed except by a back up and restore operation. Use the dump command to
back up the file system. You can then reset the partition sizes manually and restore the file system to the storage device.
ERRORS
The disklabel command produces output similar to that of the newfs command. If a list of disk blocks is not displayed on the terminal, the
command has failed. Verify the partition settings and the mount status of the target file system.
The disklabel command does not permit you to overwrite a partition if it is in use. Refer to the disklabel(8) reference page for more
information on label errors.
FILES
Specifies the command path.
RELATED INFORMATION
diskconfig(8), disklabel(8), mount(8), and fstab(4).
extendfs(8)