Is there a way to run
or
on LPAR, since LPAR doesn't have any console or it is connected to HMC
usually the way is to export the display to some PC which has Xmanager running on it, but in my case, I want to run xmanager [startx] on the AIX Lpar and run on it the xclock
In the attachment,
the ones that show localhost
while on cloapp, it shows
support is = 10.1.1.71
How can I make CLOAPP same as oradb (which is localhost on the XMANAGER )
Hi,
I define 2 new LV on the vio server and run a cfgmgr on the partition and see my 2 new hdisk (hdisk6 and hdisk7).
I extend my vg vg000 (on the partition) and add the 2 hdisks.
I had a filesystem on the vg000 and when I added the disk I would like to increase the filesystem. But I cannot do a... (0 Replies)
Question is on setting of Physical and Virtual processors for LPARs to make proper use of virtualization capabilities.
Environment is a 8-way p570 with 4 LPARs.
lparVIO1 and lparVIO2:
AIX 5300-04-01
Mode/Type= Shared-SMT/Capped
Minimum Processors= 0.10
Desired Processors= 0.50
Maximum... (1 Reply)
I have clean installed AIX6.1 in this partition.
I want to run xclock but it fail to run :(
I have launch export DISPLAY=10.23.17.60:0
Then launch xclock but it will produce some error saying it failed.
Error: Can't open display: 10.23.177.60:0
When i try to google around, some say... (5 Replies)
I just wondering if there are ways to open multiple virtual terminal to a single LPAR.
After I have use putty to login to the VIOS. I will use mkvt -id <LPAR id> to open console but if my friend want to open 2 second one, it will say, VT already connected.
IS there a way to work this around ? ... (1 Reply)
Hi all,
I have the following configuration
2 ds3524 storage disk systems located over 2 locations
2 P720 server located over 2 locations
DS3524 are connected to san switch.
Each vio server has 1 fc adapter attached to a san switch.
per p720 server 2 virtual io servers. Vio 1 has 1 lun... (2 Replies)
Hello, hopefully someone can help me out with this, I have created a virtual Ethernet adapter on the VIO but would like to add it to my new LPAR.
On my VIO only my disk is mapped.
$ lsmap -all
SVSA Physloc Client Partition ID
--------------- --------------------------------------------... (5 Replies)
This is where I am getting stuck and I am wondering if I can get some help from the community.
I log into putty with X11 forward enable
echo $DISPLAY
DISPLAY=localhost:10.0
export DISPLAY
xclock ( I do see a clock)
:)
I am happy that I finally get to install Oracle 11g on solaris... (2 Replies)
Hello,
VIOS 2.2.1.4 using IVM.
I'm trying to extend a virtual disk assigned to a running lpar so that I can expand the lpar's datavg and grow some filesystems for the user.
Storage admin expanded the lun and new size was reflected in VIO right away. I then needed the storage pool to... (2 Replies)
There can be configurations in IBM Server wherein a
standalone partition is created on some supported IBM Server
Or
A VIOS - VIOC LPARs created.
Now in both cases they are lpars. But if I want to differentiate b/w a standalone LPAR vs an VIOC LPAR how can I do..?
On a... (2 Replies)
Note: Newbie to IBM virtualization :-)
Query: Created a new AIX7.1 lpar on a system with same config as one before however the new one is having issues going out to physical network.
Now on comparison the only thing which differs between these two machines is an additional en1 and ent1 shown... (7 Replies)
Discussion started by: max
7 Replies
LEARN ABOUT V7
startx
STARTX(1) General Commands Manual STARTX(1)NAME
startx - initialize an X session
SYNOPSIS
startx [ [ client ] options ... ] [ -- [ server ] [ display ] options ... ]
DESCRIPTION
The startx script is a front end to xinit(1) that provides a somewhat nicer user interface for running a single session of the X Window
System. It is often run with no arguments.
Arguments immediately following the startx command are used to start a client in the same manner as xinit(1). The special argument '--'
marks the end of client arguments and the beginning of server options. It may be convenient to specify server options with startx to
change on a per-session basis the default color depth, the server's notion of the number of dots-per-inch the display device presents, or
take advantage of a different server layout, as permitted by the Xorg(1) server and specified in the xorg.conf(5) configuration. Some
examples of specifying server arguments follow; consult the manual page for your X server to determine which arguments are legal.
startx -- -depth 16
startx -- -dpi 100
startx -- -layout Multihead
To determine the client to run, startx first looks for a file called .xinitrc in the user's home directory. If that is not found, it uses
the file xinitrc in the xinit library directory. If command line client options are given, they override this behavior and revert to the
xinit(1) behavior. To determine the server to run, startx first looks for a file called .xserverrc in the user's home directory. If that
is not found, it uses the file xserverrc in the xinit library directory. If command line server options are given, they override this
behavior and revert to the xinit(1) behavior. Users rarely need to provide a .xserverrc file. See the xinit(1) manual page for more
details on the arguments.
The system-wide xinitrc and xserverrc files are found in the /etc/X11/xinit directory.
ENVIRONMENT VARIABLES
DISPLAY This variable gets set to the name of the display to which clients should connect. Note that this gets set, not
read.
XAUTHORITY This variable, if not already defined, gets set to $(HOME)/.Xauthority. This is to prevent the X server, if not
given the -auth argument, from automatically setting up insecure host-based authentication for the local host.
See the Xserver(1) and Xsecurity(7) manual pages for more information on X client/server authentication.
FILES
$(HOME)/.xinitrc Client to run. Typically a shell script which runs many programs in the background.
$(HOME)/.xserverrc Server to run. The default is X.
/etc/X11/xinit/xinitrc Client to run if the user has no .xinitrc file.
/etc/X11/xinit/xserverrc Server to run if the user has no .xserverrc file.
SEE ALSO xinit(1), X(7), Xserver(1), Xorg(1), xorg.conf(5)X Version 11 xinit 1.3.2 STARTX(1)