Hey Everybody,
I am having much trouble figuring this out, as I am not really a programmer..:mad:
Datafile.txt
Column0 Column1 Column2
ABC DEF xxxGHI
I am running using WGET on a cronjob to grab a datafile, but I need to cut the first three characters from... (6 Replies)
I have a large flat file with variable length fields that are pipe delimited. The file has no new line or CR/LF characters to indicate a new record. I need to parse the file and after some number of fields, I need to insert a CR/LF to start the next record.
Input file ... (2 Replies)
Hi All
I wanted to know how to effectively delete some columns in a large tab delimited file.
I have a file that contains 5 columns and almost 100,000 rows
3456 f g t t
3456 g h
456 f h
4567 f g h z
345 f g
567 h j k lThis is a very large data file and tab delimited.
I need... (2 Replies)
Since there are approximately 75K gsfiles and hundreds of stfiles per gsfile, this script can take hours. How can I rewrite this script, so that it's much faster? I'm not as familiar with perl but I'm open to all suggestions.
ls file.list>$split
for gsfile in `cat $split`;
do
csplit... (17 Replies)
Hi ,
I have the following file which is basically a grid (has more than 100000 rows)
LLL1 PPP1
LLL1 PPP2
LLL1 PPP3
...............
LLL1 5500
.....
LLL2 PPP1
LLL2 PPP2
LLL2 PPP3
...............
LLL1 5500
.....
L100 PPP1
L100 PPP2
L100 PPP3
...............
2100 5500... (6 Replies)
Hello folks, I have another doozy. I have two files. The first file has four fields in it. These four fields map to different locations in my second file. What I want to do is read the master file (file 2 - 23 fields) and compare each line against each record in file 1. If I get a match in all four... (4 Replies)
Hello,
I have a very large dictionary file which is in text format and which contains a large number of sub-sections. Each sub-section starts with the following header :
#DATA
#VALID 1
and ends with a footer as shown below
#END
The data between the Header and the Footer consists of... (6 Replies)
Hi,
I am new in perl.
I am running a perl installation script, its asking for paths and so many inputs.
Can we provide that info by any file.
so i can avoid the interactive installation. (2 Replies)
Discussion started by: Priy
2 Replies
LEARN ABOUT SUSE
irsend
IRSEND(1) FSF IRSEND(1)NAME
irsend - basic LIRC program to send infra-red commands
SYNOPSIS
irsend [options] DIRECTIVE REMOTE CODE [CODE...]
DESCRIPTION
Asks the lircd daemon to send one or more CIR (Consumer Infra-Red) commands. This is intended for remote control of electronic devices such
as TV boxes, HiFi sets, etc.
DIRECTIVE can be:
SEND_ONCE - send CODE [CODE ...] once
SEND_START - start repeating CODE
SEND_STOP - stop repeating CODE
LIST - list configured remote items
SET_TRANSMITTERS - set transmitters NUM [NUM ...]
SIMULATE - simulate IR event
REMOTE is the name of a remote, as described in the lircd configuration file.
CODE is the name of a remote control key of REMOTE, as it appears in the lircd configuration file.
NUM is the transmitter number of the hardware device.
For the LIST DIRECTIVE, REMOTE and/or CODE can be empty:
LIST "" "" - list all configured remote names
LIST REMOTE "" - list all codes of REMOTE
LIST REMOTE CODE - list only CODE of REMOTE
The SIMULATE command only works if it has been explicitly enabled in lircd.
-h --help
display usage summary
-v --version
display version
-d --device
use given lircd socket [/var/run/lirc/lircd]
-a --address=host[:port]
connect to lircd at this address
-# --count=n
send command n times
EXAMPLES
irsend LIST DenonTuner ""
irsend SEND_ONCE DenonTuner PROG-SCAN
irsend SEND_ONCE OnkyoAmpli VOL-UP VOL-UP VOL-UP VOL-UP
irsend SEND_START OnkyoAmpli VOL-DOWN ; sleep 3
irsend SEND_STOP OnkyoAmpli VOL-DOWN
irsend SET_TRANSMITTERS 1
irsend SET_TRANSMITTERS 1 3 4
irsend SIMULATE "0000000000000476 00 OK TECHNISAT_ST3004S"
FILES
/etc/lirc/lircd.conf
Default lircd configuration file. It should contain all the remotes, their infra-red codes and the corresponding timing and wave-
form details.
DIAGNOSTICS
If lircd is not running (or /var/run/lirc/lircd lacks write permissions) irsend aborts with the following diagnostics:
"irsend: could not connect to socket"
"irsend: Connection refused" (or "Permission denied").
SEE ALSO
The documentation for lirc is maintained as html pages. They are located under html/ in the documentation directory.
lircd(8), mode2(1), smode2(1), xmode2(1), irrecord(1), irw(1), http://www.lirc.org.
irsend 0.8.7pre1 May 2010 IRSEND(1)