I am installing Red Hat Linux 6.9 as a VM in Hyper-V on an HP laptop running Windows 10. After the install completes and the VM reboots, it gives me the message, "Detected CPU Family 6 model 142; Warning: Intel CPU model - this hardware has not undergone testing by Red Hat and might not be certified" (see screenshot). I also got this message when installing Red Hat Linux 6.7, but Linux booted up fine after getting that message. Now, with 6.9, after I get that message, I get a black screen with a funny looking bar across the top of it and then it just hangs (see screenshot). Anyone else experienced this issue or does anyone have any suggestions?
i'm having 2 problems.
1. the system will always look to boot from the net. i've changed the prom settings so that it boots from the disk, by entering "setenv boot-device disk0:3", but the system still seems to want to boot from the net.
2. i replaced my creator3d with an elitem6 and i did... (6 Replies)
hardware on my first FreeBSD server has crashed. i was planning on
swapping the HD into another machine, booting the generic kernel and then
custom tailoring it to the new machine specs.
however, i'm having a problem.
the new machine is using a promise ultra100 card. i don't have any... (2 Replies)
I have a client with a V1280 onsite and it is having boot problems. Below is the message it is returning when trying to boot. Is this something that anybody has run into, or that you might be able to shed some light on?
{0} ok boot
/ssm@0,0/pci@18,700000/ide@3/cdrom@0,0:f
SunOS Release 5.9... (3 Replies)
Hello those more knowledgeable than I:
I have been trying to get xp and SCO to coexist on the same system. I have tried several different ways to make both work, here's the list:
-install xp, image it, move the partition to the end of drive, verify it boots, image again,
-boot off of SCO... (6 Replies)
I have a pentium IV with 512 MB ram and 80 GB HDD.
I first installed windows XP on the first primary partition, then Solaris on the second with 20 GB for the solaris partition, and when rebooted , the grub menu functioned as expected giving me the options to dual boot, so next I wanted to install... (3 Replies)
Hello,
I've a very weird problem with one of the machines. When I try to boot off a working DVD that I used to install another system with it spits out the following message:
Sun Fire V440, No Keyboard
Copyright 2007 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.22.33, 8192 MB... (14 Replies)
I 'm trying to configure a WAN boot server on Solaris10 x86 for sparc clients ..
when i try to set up the server m getting following error
./setup_install_server -w /var/apache2/htdocs/wanboot10/wpath /var/apache2/htdocs/wanboot10/ipath
ERROR: Cannot make WAN boot Image file on this... (6 Replies)
Discussion started by: fugitive
6 Replies
LEARN ABOUT OPENSOLARIS
lx
lx(5) Standards, Environments, and Macros lx(5)NAME
lx - Linux branded zone
DESCRIPTION
The lx brand uses the branded zones framework described in brands(5) to enable Linux binary applications to run unmodified on a machine
with a Solaris Operating System kernel.
The lx brand includes the tools necessary to install a CentOS 3.x or Red Hat Enterprise Linux 3.x distribution inside a non-global zone.
The brand supports the execution of 32-bit Linux applications on x86/x64 machines running the Solaris system in either 32-bit or 64-bit
mode.
Supported Linux Distributions
The lx brand emulates the system call interfaces provided by the Linux 2.4.21 kernel, as modified by Red Hat in the RHEL 3.x distributions.
This kernel provides the system call interfaces consumed by the glibc version 2.3.2 released by Red Hat.
In addition, the lx brand partially emulates the Linux /dev and /proc interfaces.
Configuration and Administration
The lx brand supports the whole root non-global zone model. All of the required linux packages are installed into the private file systems
of the zone.
The zonecfg(1M) utility is used to configure an lx branded zone. Once a branded zone has been installed, that zone's brand cannot be
changed or removed. The zoneadm(1M) utility is used to report the zone's brand type and administer the zone. The zlogin(1) utility is used
to log in to the zone.
Application Support
The lx zone only supports user-level Linux applications. You cannot use Linux device drivers, Linux kernel modules, or Linux file systems
from inside an lx zone.
You cannot add any non-standard Solaris devices to a Linux zone. Any attempt to do so will result in a zone that zonecfg(1M) will refuse to
verify.
You cannot run Solaris applications inside an lx zone. Solaris debugging tools such as DTrace (see dtrace(1M)) and mdb (see mdb(1)) can be
applied to Linux processes executing inside the zone, but the tools themselves must be running in the global zone. Any core files generated
are produced in the Solaris format, and such files can only be debugged with Solaris tools.
ATTRIBUTES
See attributes(5) for a description of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWlxr, SUNWlxu |
+-----------------------------+-----------------------------+
|Interface Stability |Evolving |
+-----------------------------+-----------------------------+
SEE ALSO mdb(1), zlogin(1), zonename(1), dtrace(1M), zoneadm(1M), zonecfg(1M), brands(5), zones(5), lx_systrace(7D)SunOS 5.11 19 Sep 2006 lx(5)