By Size in Blocks - would this give an idea of how much size it occupies in GB ?
But i see the parent directory of this dir has a lower block size.. So i am a little confused.
The size of the directory is not the size of the blocks, but rather the product of blocksize and number of blocks used. Consider this on my system:
Both file and dir occupy a single 4096 byte-sized block. ls shows the size of the file regardless of the amount of disk space it occupies. The directory, on the other hand, appears to fit the block it occupies. As you add more to the file it grows until it occupies two, three, or even twenty blocks. Think of the directory as look-up table, containing two fields per record: the name of the file it "contains", and the files inode number. As you add files to the directory it fills up the table until there is no more room, at which point it will grow into a second block. Now look at the number of links if your two directories. Evidently job contains more files than logs, requiring it to use more disk space Hence the discrepancy.
I should point out that I don't know the full workings of file systems; I don't really need to. The above assumptions just give me that warm, fuzzy feeling that I need to use them.
I am getting a variable as x=2006/01/18
now I have to extract each field from it.
Like x1=2006, x2=01 and x3=18.
Any idea how?
Thanks a lot for help.
Thanks
CSaha (6 Replies)
Hi guys,
I couldn't find solution to this problem. If anyone knows please help me out.
your guidance is highly appretiated.
I have two files -
FILE1 has the following 7 columns ( - has been added to make columns visible enough else columns are separated by single space)
155.34 - leg - 1... (8 Replies)
Hi,
I am writing a code where the file is a pipe delimited and I would need to extract the 2nd part of field2 if it is "ATTN", "C/O" or "%" and check to see if field9 is populated or not. If field9 is already populated then leave it as is but if field9 is not populated then take the 2nd part of... (3 Replies)
Hi All,
Looking for a quick AWK script to output some differences between two files.
FILE1
device1 1.1.1.1 PINGS
device1 2.2.2.2 PINGS
FILE2
2862 SITE1 device1-prod 1.1.1.1 icmp - 0 ... (4 Replies)
Diff output as follows:
< AAA BBB CCC DDD EEE 123
> PPP QQQ RRR SSS TTT 111
> VVV WWW XXX YYY ZZZ 333
> AAA BBB CCC DDD EEE 124
How can i use awk to compare the last field to determine if the counter has increased, and need to ensure that the first 4 fields must have the same... (15 Replies)
Attached is a file called diff.txt
It is the output from this command:
diff -y --suppress-common-lines --width=5000 1.txt 2.txt > diff.txt
I have also attached 1.txt and 2.txt for your convenience.
Both 1.txt and 2.txt contain one very long CSV string.
File 1.txt is a CSV dump of... (0 Replies)
Hi All,
I am using the following command in Linux:
sar -r 30 3
Linux 2.6.18-194.3.1.7.3.el5xen 02/07/2013
02:55:47 PM kbmemfree kbmemused %memused kbbuffers kbcached kbswpfree kbswpused %swpused kbswpcad
02:56:17 PM 128646024 22348920 14.80 230232 15575860 75497464 ... (4 Replies)
In our environment we used to lot of events for ntp issues. I am unable to find the what needs to consider here. :(
ntpq -p fields.
remote refid st t when poll reach delay offset jitter
---------- Post updated at 05:13 AM ---------- Previous update was at 04:47 AM... (1 Reply)
I need to print field and the next one if field matches 'patternA' and also print 'patternB' fields.
echo "some output" | awk '{for(i=1;i<=NF;i++){if($i ~ /patternA/){print $i, $(i+1)}elif($i ~ /patternB/){print $i}}}'
This code returnes me 'syntax error'. Pls advise how to do properly. (2 Replies)