Hmmmmm.......so both members of the RAID are shown as present and active....good.
So this RAID is on device /dev/md0
(After the RAID is create you should never address these disks as their original devices (/dev/dsk/... or whatever the format is on Ubuntu), only as /dev/md0.
What command are you using to mount the RAID where you want it? Are you specifying /dev/md0? If so, the system should know that it's a RAID mirror and if one disk fails, access to data on the surviving copy should remain.
Hi,
I am facing problem while accessing samba share on Linux 5.1 from windows, though I have done the same configuration on Linux 4 (Update 2), on Red Hat 4.0 it is working but while on Linux 5.1 these configuration are not working, I have disabled the firewall also.
Kindly suggest me... (1 Reply)
Hi everyone! I'm trying to run a script when a folder is shared and when it stop being shared.
Is there something like .start_share or .stop_share scripts in Samba where I could run some commands?:confused:
edit: maybe with a wrapper in smbmount but I share folders via nautilus. Any ideas? (0 Replies)
Hi I have an issue with a client. He was able to use his mounted Samba share for a long time. However, a couple of days ago, he wasn't able to access all of his files all of a sudden. He still see's the share and majority of the files, but not some that he needs.
I checked with Secure CRT on... (1 Reply)
Hi All, I've been trying to configure samba on Solaris 10 to allow me to have one share that is open and writable to all users and have the rest of my shares password protected by a generic account.
If I set my security to user, my secured shares work just fine and prompt accordingly, but when... (0 Replies)
I am setup a samba share server which is authenticating from Active Directory.
I am able to access the share with AD user but not able to access when group defined in "valid users" parameters.
below are the steps i performed.
In smb.conf
workgroup = QASLABS
password server =... (3 Replies)
Hi ,
In samba i have shared my home directory,
but its showing as a printer.
Not able to share data.
$ smbclient -L 192.168.122.1
Enter priyank's password:
Domain= OS= Server=
Sharename Type Comment
--------- ---- -------
shared_priyank Printer ... (3 Replies)
Hello,
I want to connect to two samba shares both on the same Linux box but each with a different username from a windows server 2008. I created 2 gpos to connect and I can connect to the shares individually via net use command, but once I entered credentials for one of the shares, it seems I... (1 Reply)
Long running samba share. Never have any problems,
Suddenly started asking windows users for password - which doesnt work. Tried to manually reset smb password and manually map - still wrong password.
Restart samba? (2 Replies)
Hi,
I need to mount a directory from a Windows server to a CentOS box.
The Windows server used is Windows Server 2003, and the path to the directory that I want to mount on CentOS is C:\Tomcat6\webapps\NASApp\logs.
I am not sure of the correct way to mount this on CentOS, as most of the... (2 Replies)
Discussion started by: anaigini45
2 Replies
LEARN ABOUT SUNOS
raidctl
raidctl(1M) System Administration Commands raidctl(1M)NAME
raidctl - RAID hardware utility
SYNOPSIS
raidctl -c disk1 disk2
raidctl -d disk1
raidctl [-f] -F filename controller...
raidctl -l [controller...]
DESCRIPTION
The raidctl utility creates, deletes, or displays RAID volumes of the LSI1030 HW Raid controllers that include RAID support. The utility
also updates firmware/fcode/BIOS for both RAID and non-RAID controllers.
The raidctl utility requires privileges that are controlled by the underlying file-system permissions. Only privileged users can manipulate
the RAID system configuration. If a non-privileged user attempts to create or delete a RAID volume, the command fails with EPERM.
Without options, raidctl displays the current RAID configuration on all exisiting controllers.
OPTIONS
The following options are supported:
-c disk1 disk2 (for on board)
Create a mirror using disk1 and disk2. Replace the contents of disk2 with the contents of disk1. Specify disk1 and disk2 in canonical
form, for example, c0t0d0.
When you create a a RAID volume, the RAID volume assumes the identity of the first target in the disk pair (disk1). The second target
(disk2) disappears from the system. Therefore, the RAID volume appears as one disk.
To have a successful RAID creation, there must not already be a RAID configuration present on the specified controller. Additionally,
the secondary disk must not be mounted, as it has all its data erased and replaced with the primary disk's data.
-d disk1 (for on board)
Delete the RAID volume specified as disk1.
Specify disk1 in canonical form, for example, c0t0d0.
-f (for HBA)
Force an update. Do not prompt.
-F filename controller (for HBA)
Update the firmware running on the specified controller (controller).
-l [controller ...] (for on board)
List the system's RAID configuration. If controller is specified, list RAID configurations for controller.
Output from the -l lists the following information:
RAID Volume Displays logical RAID volume name.
RAID Status Displays RAID status as either RESYNCING (disks are syncing), DEGRADED RAID is operating with reduced functionality),
OK (operating optimally), or FAILED (non-functional).
RAID Disk Displays RAID disk name.
Disk Status Displays disk status as either OK or FAILED.
EXAMPLES
Example 1: Creating the RAID Configuration
The following command creates the RAID configuration:
# raidctl -c c0t0d0 c0t1d0
RAID Volume 'c0t0d0' created
Example 2: Displaying the RAID Configuration
The following command displays the RAID configuration:
# raidctl
RAID RAID RAID Disk
Volume Status Disk Status
----------------------------------------
c0t0d0 RESYNCING c0t0d0 OK
c0t1d0 OK
Example 3: Deleting the RAID Configuration
The following command deletes the RAID configuration:
# raidctl -d c0t0d0
RAID Volume 'c0t0d0' deleted
Example 4: Updating Flash Images on the Controller
The following command updates flash images on the controller:
# raidctl -F lsi1030.fw 0
Update flash image on controller 0? (y/N): y
Flash updated successfully
EXIT STATUS
The following exit values are returned:
0 Successful completion.
1 Invalid command line input.
2 Request operation failed.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|Availability |SUNWcsu |
+-----------------------------+-----------------------------+
SEE ALSO attributes(5)
System Administration Guide: Basic Administration
SunOS 5.10 17 Aug 2004 raidctl(1M)