So the system is now installed on c1t0025385971B16535d0 (using whole disk), and zpool import complains of that same disk being part of fido zpool which contains the same device c1t0025385971B16535d0 ?
This is quite strange.
Can we see the output of :
Also format command and print partitions of that disk would be helpful.
Previously , i remove the disk by
#vxdg -g testdg -k rmdisk testdg02
But i got error when i -k adddisk
bash-2.03# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online invalid
c0t1d0s2 auto:none ... (1 Reply)
# zpool import
pool: emcpool1
id: 5596268873059055768
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: Sun Message ID: ZFS-8000-3C
config:
emcpool1 ... (7 Replies)
Hello, I have a problem on my backup server. I lost my system hdd and my separate ZIL device while the system crashs and now I'm in trouble. The old system was running under the least version of osol/dev (snv_134) with zfs v22.
After the server crashs I was very optimistic of solving the problems... (2 Replies)
I am trying to test simple zfs functionality on a FreeBSD 8.2 VM. When I try to run a 'zpool create' I receive the following error:
# zpool create zfspool /dev/da0s1a
cannot create 'zfspool': no such pool or dataset
# zpool create zfspool /dev/da0
cannot create 'zfspool': no such pool or... (3 Replies)
Hi guys, I appreciate any help in this regard, we have lost sensitive data in the company.
One box with 2 disk mirrored and a 3ware controller handling 13 disks in a raidz2 pool. Suddenly the box restart and keeps "Reading ZFS config" for hours.
Unplugging disk by disk we isolate the disk... (3 Replies)
Hi Guys,
I have a single ZFS pool with 2 disk which is mirrored if i create a new BE with lucreate should i specify which disk where the new BE should be created? (7 Replies)
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
A backup/clone script of ours was recently ran. It normally only clones the rpool and renames in rpoolA. Something must've changed as it found another one of our pools that it shouldn't have. It exported that pool unbeknownst to us. Later on when a coworker realized the other pool was missing he... (2 Replies)
I have a single zpool with 3 2-way mirrors ( 3 x 2 way vdevs) it has a degraded disk in mirror-2, I know I can suffer a single drive failure, but looking at this how many drive failures can this suffer before it is no good? On the face of it, I thought that I could lose a further 2 drives in each... (4 Replies)
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Discussion started by: rrodgers
2 Replies
LEARN ABOUT OSF1
volrootmir
volrootmir(8) System Manager's Manual volrootmir(8)NAME
volrootmir - Mirror areas necessary for booting to a new disk
SYNOPSIS
/usr/sbin/volrootmir [-a] [nconfig=count] target_disk [swap=target_partition]
OPTIONS
Specifies that all volumes on the system disk be mirrored, not just the root and swap volumes, rootvol and swapvol.
DESCRIPTION
The volrootmir script causes a mirror copy of areas of the root disk involved in booting to be made on the specified target disk.
When used without the -a option, volrootmir adds mirrors of the root and swap volumes and allocates them on the new disk. In addition, all
disk regions required for booting are set up and partitions for the new volume mirrors are created.
When used with the -a option, volrootmir mirrors all in-use partitions on the system disk.
To mirror a swap volume that is on a separate disk from the root volume, the swap attribute must be used to specify a separate target for
the swap mirror.
The target disk(s) must be at least as large as the sum of the sizes of rootvol and swapvol. Also, the physical disk should not have any
disk partition in use.
This script can be called from the voldiskadm menus by choosing the Mirror volumes on a disk operation.
ATTRIBUTES
Specifies the number of log copies and copies of the configuration database, for example, nconfig=2. Specifies that the swap volume,
swapvol, be mirrored on a separate disk, as specified by target_partition.
EXAMPLES
The following command mirrors the rootvol and swapvol volumes onto the target disk, dsk3. This command will fail if swapvol is on a differ-
ent disk from rootvol.
# volrootmir dsk3 The following command mirrors rootvol, swapvol, and any other volumes on the root disk onto the target disk, dsk3.
This command will fail if swapvol is on a different disk from rootvol.
# volrootmir -a dsk3 The following command mirrors rootvol on disk dsk3, swapvol onto partition dsk7d, and any other volumes on the
root disk onto disk dsk3. This command will fail if swapvol is on the same disk as rootvol.
# volrootmir -a dsk3 swap=dsk7d The following command mirrors rootvol onto disk dsk3 and swapvol onto partition dsk7d. This command
will fail if swapvol is on the same disk as rootvol.
# volrootmir dsk3 swap=dsk7d
SEE ALSO volintro(8), voldiskadm(8)volrootmir(8)