Previously , i remove the disk by
#vxdg -g testdg -k rmdisk testdg02
But i got error when i -k adddisk
bash-2.03# vxdisk list
DEVICE TYPE DISK GROUP STATUS
c0t0d0s2 auto:none - - online invalid
c0t1d0s2 auto:none ... (1 Reply)
# zpool import
pool: emcpool1
id: 5596268873059055768
state: UNAVAIL
status: One or more devices are missing from the system.
action: The pool cannot be imported. Attach the missing
devices and try again.
see: Sun Message ID: ZFS-8000-3C
config:
emcpool1 ... (7 Replies)
Hello, I have a problem on my backup server. I lost my system hdd and my separate ZIL device while the system crashs and now I'm in trouble. The old system was running under the least version of osol/dev (snv_134) with zfs v22.
After the server crashs I was very optimistic of solving the problems... (2 Replies)
I am trying to test simple zfs functionality on a FreeBSD 8.2 VM. When I try to run a 'zpool create' I receive the following error:
# zpool create zfspool /dev/da0s1a
cannot create 'zfspool': no such pool or dataset
# zpool create zfspool /dev/da0
cannot create 'zfspool': no such pool or... (3 Replies)
Hi guys, I appreciate any help in this regard, we have lost sensitive data in the company.
One box with 2 disk mirrored and a 3ware controller handling 13 disks in a raidz2 pool. Suddenly the box restart and keeps "Reading ZFS config" for hours.
Unplugging disk by disk we isolate the disk... (3 Replies)
Hi Guys,
I have a single ZFS pool with 2 disk which is mirrored if i create a new BE with lucreate should i specify which disk where the new BE should be created? (7 Replies)
Hi,
Quick question.
I have a data zpool that consists of 1 disk.
pool: data
state: ONLINE
scrub: none requested
config:
NAME STATE READ WRITE CKSUM
data ONLINE 0 0 0
c0t50002AC0014B06BEd0 ONLINE... (2 Replies)
A backup/clone script of ours was recently ran. It normally only clones the rpool and renames in rpoolA. Something must've changed as it found another one of our pools that it shouldn't have. It exported that pool unbeknownst to us. Later on when a coworker realized the other pool was missing he... (2 Replies)
I have a single zpool with 3 2-way mirrors ( 3 x 2 way vdevs) it has a degraded disk in mirror-2, I know I can suffer a single drive failure, but looking at this how many drive failures can this suffer before it is no good? On the face of it, I thought that I could lose a further 2 drives in each... (4 Replies)
issue,
I had a zpool which was full
pool_temp1 199G 197G 1.56G 99% ONLINE -
pool_temp2 199G 196G 3.09G 98% ONLINE -
as you can see, full
so I replaced with a larger disk.
zpool replace pool_temp1 c3t600144F0FF8BA036000058CC1DB80008d0s0... (2 Replies)
Discussion started by: rrodgers
2 Replies
LEARN ABOUT FREEBSD
zfsboot
ZFSBOOT(8) BSD System Manager's Manual ZFSBOOT(8)NAME
zfsboot -- bootcode for ZFS on BIOS-based computers
DESCRIPTION
zfsboot is used on BIOS-based computers to boot from a filesystem in a ZFS pool. zfsboot is installed in two parts on a disk or a partition
used by a ZFS pool. The first part, a single-sector starter boot block, is installed at the beginning of the disk or partition. The second
part, a main boot block, is installed at a special offset within the disk or partition. Both areas are reserved by the ZFS on-disk specifi-
cation for boot use. If zfsboot is installed in a partition, then that partition should be made bootable using appropriate configuration and
boot blocks described in boot(8).
BOOTING
The zfsboot boot process is very similar to that of gptzfsboot(8). One significant difference is that zfsboot does not currently support the
GPT partitioning scheme. Thus only whole disks and MBR partitions, traditionally referred to as slices, are probed for ZFS disk labels. See
the BUGS section in gptzfsboot(8) for some limitations of the MBR scheme support.
USAGE
zfsboot supports all the same prompt and configuration file arguments as gptzfsboot(8).
FILES
/boot/zfsboot boot code binary
/boot.config parameters for the boot block (optional)
/boot/config alternative parameters for the boot block (optional)
EXAMPLES
zfsboot is typically installed using dd(1). To install zfsboot on the ada0 drive:
dd if=/boot/zfsboot of=/dev/ada0 count=1
dd if=/boot/zfsboot of=/dev/ada0 iseek=1 oseek=1024
If the drive is currently in use, the GEOM safety will prevent writes and must be disabled before running the above commands:
sysctl kern.geom.debugflags=0x10
zfsboot can also be installed in an MBR slice:
gpart create -s mbr ada0
gpart add -t freebsd ada0
gpart create -s BSD ada0s1
gpart bootcode -b /boot/boot0 ada0
gpart set -a active -i 1 ada0
dd if=/boot/zfsboot of=/dev/ada0s1 count=1
dd if=/boot/zfsboot of=/dev/ada0s1 iseek=1 oseek=1024
Note that commands to create and populate a pool are not shown in the example above.
SEE ALSO dd(1), boot.config(5), boot(8), gptzfsboot(8), loader(8), zfsloader(8), zpool(8)HISTORY
zfsboot appeared in FreeBSD 7.3.
AUTHORS
This manual page was written by Andriy Gapon <avg@FreeBSD.org>.
BUGS
Installing zfsboot with dd(1) is a hack. ZFS needs a command to properly install zfsboot onto a ZFS-controlled disk or partition.
BSD September 15, 2014 BSD