Sponsored Content
Operating Systems Solaris Fibre channel link down on booting Solaris server Post 303020562 by fretagi on Monday 23rd of July 2018 08:46:27 AM
Old 07-23-2018
It does not boot in any of them:

for disk0, just stays like below

Code:
{0} ok boot disk0
Boot device: /pci@400/pci@1/pci@0/pci@2/@0/disk@p0  File and args:

for disk disk1 :
Code:
 ok boot disk1
Boot device: /pci@400/pci@1/pci@0/pci@2/@0/disk@p1  File and args:
ERROR: boot-read fail


Can't locate boot device

for disk2

Code:
{0} ok boot disk2
Boot device: /pci@400/pci@1/pci@0/pci@2/@0/disk@p2  File and args:
ERROR: boot-read fail


Can't locate boot device

and for disk3

Code:
{0} ok boot disk3
Boot device: /pci@400/pci@1/pci@0/pci@2/@0/disk@p3  File and args:
ERROR: boot-read fail


Can't locate boot device

{0} ok

 

7 More Discussions You Might Find Interesting

1. AIX

Fibre channel drivers on RS/6000 aix 5L

Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies

2. AIX

Power6 Virtual Fibre Channel Adapter

Hello, Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter. It is similar to virtual scsi adapter. In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies

3. Solaris

USCSICMD ioctl calls for Fibre Channel(FC) devices on Solaris 10?

Hi , I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies

4. Hardware

Fibre Channel HBA recommendations?

We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice? Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies

5. AIX

[ASK] - AIX Fibre Channel behavior

Hello all, Let me introduce about the context and my environment. We have an AIX 6.1 system, it has 4 FC channels / > lsdev -Cc adapter | grep fcs fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies

6. Solaris

Fibre Channel link not ready on Netra 240

Hi, One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too. There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies

7. Solaris

Issue with Fiber Channel cards in Solaris

hi everone i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
installboot(1M) 														   installboot(1M)

NAME
installboot - install bootblocks in a disk partition SYNOPSIS
installboot bootblk raw-disk-device The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition. The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be found using the -i option of uname(1). The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead. bootblk The name of the bootblock code. raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read- able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive. Example 1: Installing UFS Boot Block To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use: example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t0d0s0 /usr/platform/platform-name/lib/fs/ufs directory where ufs boot objects reside. /platform/platform-name/ufsboot second level program to boot from a disk or CD See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5) WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device. 11 Apr 2005 installboot(1M)
All times are GMT -4. The time now is 03:11 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy