07-12-2018
Yes, so, repeat, what I said in post#2
7 More Discussions You Might Find Interesting
1. AIX
Want to configure IBM raid strorage but the aix 5L cds do not have the drivers for the fibre channels. The machine is RS/6000. I have gone to IBM downlaodable sites but i can't find the drivers? help pliz:mad: (4 Replies)
Discussion started by: Zim-Aix-Guru
4 Replies
2. AIX
Hello,
Searched in all IBM Redbooks and on the internet and couldn't find anything about the new feature of POWER 6 which Virtual Fibre ( Fiber ) channel adapter.
It is similar to virtual scsi adapter.
In my client partition I created the virtual Fibre Adapter mapped it with the VIO... (1 Reply)
Discussion started by: filosophizer
1 Replies
3. Solaris
Hi ,
I have wrtitten a C program that issues USCSICMD ioctl call to the tape devices attached on solaris sparc 10. I was able to get the required information from all SCSI tape devices attached using the utility. But, whenever it is run on FC attached tape drives , the program returns an error... (0 Replies)
Discussion started by: naveen448
0 Replies
4. Hardware
We will be buying new Xeon E5-based servers for our datacenter and were wondering which Fibre Channel host bus adapters we should select for these. The choices are Emulex or QLogic (8Gb FC HBAs). Anybody have any recommendations on which is the better choice?
Thanks in advance. (1 Reply)
Discussion started by: atahmass
1 Replies
5. AIX
Hello all,
Let me introduce about the context and my environment.
We have an AIX 6.1 system, it has 4 FC channels
/ > lsdev -Cc adapter | grep fcs
fcs0 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs1 Available 23-T1 Virtual Fibre Channel Client Adapter
fcs2 Available 23-T1... (14 Replies)
Discussion started by: Phat
14 Replies
6. Solaris
Hi,
One of my Netra 240 went into hung state and I had to reboot it. I powered it off and tried booting it again but unsuccessful. It is not connected to SAN and have local disks. Not able to boot in failsafe mode too.
There are two disks of 72GB, both are mirrored in SVM. It complains about... (5 Replies)
Discussion started by: solaris_1977
5 Replies
7. Solaris
hi everone
i am experiencing disconnectivity from storage to My database machines. i have doubt on my FC cards in my sparc T4-2 machines. i want to know how should i check from my solaris that whether the cards are ok or not because once the disks get disconnect from SAN so it come back again but... (5 Replies)
Discussion started by: janakors
5 Replies
LEARN ABOUT DEBIAN
dch-repeat
DCH-REPEAT(1) General Commands Manual DCH-REPEAT(1)
NAME
dch-repeat - repeats a changelog entry into an older release
SYNOPSIS
dch-repeat --build-tree <PATH>
dch-repeat --source-release <RELEASE>
dch-repeat --target-release <RELEASE>
dch-repeat --devel-release <RELEASE>
dch-repeat --pocket <POCKET>
dch-repeat -h
DESCRIPTION
dch-repeat is used to repeat a changelog into an older release. It expects that --build-tree is laid out with each Ubuntu release as a
separate directory ("feisty", "edgy", etc).
For example, if gimp had a security update prepared for Feisty in $TREE/feisty/gimp-2.2.13, running dch-repeat in $TREE/edgy/gimp-2.2.13
would pull in the latest changelog from the Feisty build.
OPTIONS
Listed below are the command line options for dch-repeat:
-h or --help
Display a help message and exit.
--build-tree PATH
Base of build trees. Default is /scratch/ubuntu/build.
-s or --source-release RELEASE
Which release to take changelog from.
--target-release RELEASE
Which release to build into.
--devel-release RELEASE
Which release is the development release.
--pocket POCKET
Which pocket to use.
AUTHOR
dch-repeat was written by Kees Cook <kees@ubuntu.com>. This manual page was written by Jonathan Patrick Davies <jpds@ubuntu.com>.
Both are released under the GNU General Public License, version 2.
SEE ALSO
dch(1).
ubuntu-dev-tools 10 August 2008 DCH-REPEAT(1)