07-11-2018
@Lord Spectre,
An instruction will be there in READEME file check for that and make sure to not skip any steps.
Thanks & Regards,
Bobin Lonston
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies
5. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
6. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
7. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
8. AIX
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT OPENSOLARIS
sync_instruction_memory
sync_instruction_memory(3C) Standard C Library Functions sync_instruction_memory(3C)
NAME
sync_instruction_memory - make modified instructions executable
SYNOPSIS
void sync_instruction_memory(caddr_t addr, int len);
DESCRIPTION
The sync_instruction_memory() function performs whatever steps are required to make instructions modified by a program executable.
Some processor architectures, including some SPARC processors, have separate and independent instruction and data caches which are not
kept consistent by hardware. For example, if the instruction cache contains an instruction from some address and the program then stores a
new instruction at that address, the new instruction may not be immediately visible to the instruction fetch mechanism. Software must
explicitly invalidate the instruction cache entries for new or changed mappings of pages that might contain executable instructions. The
sync_instruction_memory() function performs this function, and/or any other functions needed to make modified instructions between addr and
addr+len visible. A program should call sync_instruction_memory() after modifying instructions and before executing them.
On processors with unified caches (one cache for both instructions and data) and pipelines which are flushed by a branch instruction, such
as the x86 architecture, the function may do nothing and just return.
The changes are immediately visible to the thread calling sync_instruction_memory() when the call returns, even if the thread should
migrate to another processor during or after the call. The changes become visible to other threads in the same manner that stores do; that
is, they eventually become visible, but the latency is implementation-dependent.
The result of executing sync_instruction_memory() are unpredictable if addr through addr+len-1 are not valid for the address space of the
program making the call.
RETURN VALUES
No values are returned.
ATTRIBUTES
See attributes(5) for descriptions of the following attributes:
+-----------------------------+-----------------------------+
| ATTRIBUTE TYPE | ATTRIBUTE VALUE |
+-----------------------------+-----------------------------+
|MT-Level |MT-Safe |
+-----------------------------+-----------------------------+
SEE ALSO
attributes(5)
SunOS 5.11 12 Feb 1997 sync_instruction_memory(3C)