07-11-2018
Quote:
Originally Posted by
hicksd8
Thank you I downloaded the igb-5.3.5.18.tar.gz driver and I seen it supports Red Hat Enterprise Linux 7.2, perfect for me. Now, how can I install it on RHEL 7?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
Discussion started by: mono673
1 Replies
2. Solaris
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Discussion started by: tubbyrana
2 Replies
3. Solaris
hi all,
How to install onboard ethernet card on Sun SPARC M4000 server? (3 Replies)
Discussion started by: Tlg13team
3 Replies
4. AIX
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
Discussion started by: sekarsamy
1 Replies
5. AIX
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Discussion started by: johnf
1 Replies
6. Red Hat
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Discussion started by: chidhu.anu
4 Replies
7. Hardware
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Discussion started by: Lhao
5 Replies
8. AIX
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Discussion started by: jayadeava
4 Replies
9. Solaris
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
Discussion started by: bentech4u
4 Replies
10. SCO
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT DEBIAN
if_ixgbe
IXGBE(4) BSD Kernel Interfaces Manual IXGBE(4)
NAME
ixgbe -- Intel(R) 10Gb Ethernet driver for the FreeBSD operating system
SYNOPSIS
To compile this driver into the kernel, place the following line in your kernel configuration file:
device ixgbe
Alternatively, to load the driver as a module at boot time, place the following line in loader.conf(5):
if_ixgbe_load="YES"
DESCRIPTION
The ixgbe driver provides support for PCI 10Gb Ethernet adapters based on the Intel 82598EB Intel(R) Network Connections. The driver sup-
ports Jumbo Frames, MSIX, TSO, and RSS.
For questions related to hardware requirements, refer to the documentation supplied with your Intel 10GbE adapter. All hardware requirements
listed apply to use with FreeBSD.
Support for Jumbo Frames is provided via the interface MTU setting. Selecting an MTU larger than 1500 bytes with the ifconfig(8) utility
configures the adapter to receive and transmit Jumbo Frames. The maximum MTU size for Jumbo Frames is 16114.
This driver version supports VLANs. For information on enabling VLANs, see ifconfig(8).
HARDWARE
The ixgbe driver supports the following cards:
o Intel(R) 10 Gigabit XF SR/AF Dual Port Server Adapter
o Intel(R) 10 Gigabit XF SR/LR Server Adapter
o Intel(R) 82598EB 10 Gigabit AF Network Connection
o Intel(R) 82598EB 10 Gigabit AT CX4 Network Connection
DIAGNOSTICS
ixgbe%d: Unable to allocate bus resource: memory A fatal initialization error has occurred.
ixgbe%d: Unable to allocate bus resource: interrupt A fatal initialization error has occurred.
ixgbe%d: watchdog timeout -- resetting The device has stopped responding to the network, or there is a problem with the network connection
(cable).
SUPPORT
For general information and support, go to the Intel support website at: http://support.intel.com.
If an issue is identified with the released source code on the supported kernel with a supported adapter, email the specific information
related to the issue to <freebsdnic@mailbox.intel.com>.
SEE ALSO
arp(4), netintro(4), ng_ether(4), polling(4), vlan(4), ifconfig(8)
HISTORY
The ixgbe device driver first appeared in FreeBSD 7.0.
AUTHORS
The ixgbe driver was written by Intel Corporation <freebsdnic@mailbox.intel.com>.
BSD
June 11, 2008 BSD