I have installed in the server a quad ethernet adapter, I'm using two interfaces with two different IP networks, both interfaces are connected to a switch, the switch report that is receiving the same MAC address in both ports so must of the times I have connectivity problems.
Any idea to change... (1 Reply)
I have a Dual Boot system - XP with Solaris 10. I built the system from the ground up with different components and the Ethernet Card built into the Motherboard is a Marvell Yukon Gigabit Ethernet 10/100/1000 T-base, RJ-45 Copper.
I am unable to go to the Web as the Ethernet Card is still not... (2 Replies)
Hi,
In our AIX 5.2 server , we have one unused ethernet adapter which doesn't have cable connection . For this interface , we are getting alerts in errpt .
Could you suggesthow to stop this alert ? And sametime i would like to keep this device in ODM .
Is there... (1 Reply)
All
I am trying allocate an IVE to an LPAR (not a VIO) running AIX 7.1. I am getting the error:
HSCL068A
Explanation
Logical port can not be assigned to Logical Partition because this Logical Partition is not the promiscuous LPAR for the physical port.
Has anyone encountered this... (1 Reply)
Hi,
I have installed Oracle Enterprise Linux 5 in my PC. After the installation the Ethernet Card is not got detected.
But I could able to get the details using the command lspci -a:
01:00.0 Ethernet controller: Attansic Technology Corp. L1 Gigabit Ethernet Adapter (rev b0).
But I could... (4 Replies)
Hi,
Does anybody have a "Sun 10-Gigabit Ethernet Adapter installation CD" or driver ixge for Sun 10-Gigabit Ethernet PCI-X adapter? I need it but can't find it anywhere. So if you know where I can download it or purchase it, please let me know. (Already tried Oracle's website, don't have it) ... (5 Replies)
Hi Techies,
I have a doubt.
ent0 Available Logical Host Ethernet Port (lp-hea)
ent1 Available Logical Host Ethernet Port (lp-hea)
ent2 Available Logical Host Ethernet Port (lp-hea)
ent3 Available Logical Host Ethernet Port (lp-hea)
ent4 Available... (4 Replies)
Hi Community,
i have one issue with 10 fiber ethernet adapter.
here is my details:
root@new-bpel.example.com #dladm show-dev
bge0 link: unknown speed: 0 Mbps duplex: unknown
bge1 link: up speed: 1000 Mbps duplex: full
qlge2 link:... (4 Replies)
hi .I've installed an operating system SCO in HP Z400 and network cards ZyXEL model FN312 with Chipset RTL8139D put it on .network card installed but do not display network card with command ifconfig -a in list and just show loopback.
show message :
dlpid:unable to open network adapter driver... (14 Replies)
Discussion started by: moein.mojtaba
14 Replies
LEARN ABOUT SUSE
rmmod
RMMOD(8)RMMOD(8)NAME
rmmod - simple program to remove a module from the Linux Kernel
SYNOPSIS
rmmod [ -f ] [ -w ] [ -s ] [ -v ] [ modulename ]
DESCRIPTION
rmmod is a trivial program to remove a module (when module unloading support is provided) from the kernel. Most users will want to use
modprobe(8) with the -r option instead.
OPTIONS -v --verbose
Print messages about what the program is doing. Usually rmmod prints messages only if something goes wrong.
-f --force
This option can be extremely dangerous: it has no effect unless CONFIG_MODULE_FORCE_UNLOAD was set when the kernel was compiled.
With this option, you can remove modules which are being used, or which are not designed to be removed, or have been marked as
unsafe (see lsmod(8)).
-w --wait
Normally, rmmod will refuse to unload modules which are in use. With this option, rmmod will isolate the module, and wait until the
module is no longer used. Nothing new will be able to use the module, but it's up to you to make sure the current users eventually
finish with it. See lsmod(8)) for information on usage counts.
-s --syslog
Send errors to syslog instead of standard error.
-V --version
Show version of program and exit.
COPYRIGHT
This manual page originally Copyright 2002, Rusty Russell, IBM Corporation. Maintained by Jon Masters and others.
SEE ALSO modprobe(8), insmod(8), lsmod(8)modinfo(8)
2010-03-01 RMMOD(8)