Sponsored Content
Top Forums UNIX for Beginners Questions & Answers Sco openserver 6 on hd sata: cloning Post 303019935 by jgt on Tuesday 10th of July 2018 11:06:06 AM
Old 07-10-2018
Download and install Microlite Edge. Microlite Corporation - Home of BackupEDGE 3.x then do a backup to DVD, you may need two disks for the 42gb of disk space used.
Create the emergency boot dvd.
Temporarily replace the 1tb disk and boot from the recovery dvd to do a full restore.

You can do this with the demo version of Edge, but only for 60 days.
When you create the new disk, only use 100gb for the Unix partition rather than the whole terabyte.
Do you have a plan for updating the backup disk with current data, assuming that the application is not read only?
This will not work if your application is copy protected and you cannot re-license it, as files will not have the same inode number on the new disk.

You should expect to spend 4 hours doing this.
This User Gave Thanks to jgt For This Post:
 

10 More Discussions You Might Find Interesting

1. UNIX for Dummies Questions & Answers

Help For SCO OpenServer

I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies

2. UNIX for Dummies Questions & Answers

sco openserver 5.5

hello! when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ? kindly help me thanks (1 Reply)
Discussion started by: buntty
1 Replies

3. UNIX for Advanced & Expert Users

SCO 5.0.2 openserver

I am doing some work for a customer that is running SCO 5.0.2 openserver and they have lost their cd. Is there anyplace I can download it? I have a replacement being shipped but it will not be here for two days and they are down. Any ideals? (3 Replies)
Discussion started by: SCOoT
3 Replies

4. UNIX for Dummies Questions & Answers

SCO Openserver 6.0

Hi guys, I just got this new 6.0 version and i'm trying to setup a remote office to telnet to this server running sco 6.0, in previous version all i have to do is add this file under /etc/rc2.d call S99route and put the gate in that file and that was it, for some reason in 6.0 it does not... (1 Reply)
Discussion started by: josramon
1 Replies

5. SCO

sco openserver 5.0.7

Dear members when i installed dual processor patch in openserver 5.0.7 in hp ML370 G4 server it hangs in sco at G_hd_config. i tried MP4, EFS 5.64,5.70A but not solved the problem.. (0 Replies)
Discussion started by: M_farooqui
0 Replies

6. SCO

SATA AHCI Tape on SCO 5.0.7

Dear all, I'm newbie in SCO. I already purchase SCO 5.0.7 and SATA Tape Drive (not SCSI) for IBM server. not a cheap investment :( my problem is: I can't use my sata tape on sco 5.0.7 for backup my data because sco can't detect any sata tape has been plug into o/s. i already running "mkdev... (7 Replies)
Discussion started by: asumatezuka
7 Replies

7. SCO

SATA Hard Disk support by SCO OpenServer 5.05

Is SATA hard disk is suooprted by SCO OpenServer 5.05? If No, how to couter this problem. If yes, please provide the installation steps. (2 Replies)
Discussion started by: rakeshkumar9919
2 Replies

8. Hardware

Connect SATA Laptop HardDrive to Desktop SATA Slots

Hello everybody, I need to connect a laptop 2.5 SATA hard drive to a Desktop board (which uses 3.5' SATA hard drives). I've tried the connectors and they fit excellent in the 2.5 SATA connectors. The problem is that the laptop hard drive uses 5v and the PC's power source sends 12v. So, my... (4 Replies)
Discussion started by: Zykl0n-B
4 Replies

9. SCO

Install Hang OpenServer 6 - SATA CDROM

Hi all Can anybody offer any help with installing Openserver 6 on a Supermicro server? I am familiar with installing OS5, but this is my first time with v6. The PC is fitted with Supermicro X8DTL-I Dual Xeon motherboard and 2 Xeon E5620 processors, and 16Gb Ram, LSI MegaRaid SAS8708 8 port... (11 Replies)
Discussion started by: millosman
11 Replies

10. SCO

SCO Unix 5.0.6 SATA in compatibility mode

I am very new to SCO Unix so I apologize if this is a easy or dumb question. I have a 160GB SATA hard drive and SATA CD-ROM drive connected to one of my systems. I have both the drives running in compatibility mode. I also have the hard drive set as a primary master and the CD-ROM drive set as... (10 Replies)
Discussion started by: NPIGuy
10 Replies
installboot(1M) 														   installboot(1M)

NAME
installboot - install bootblocks in a disk partition SYNOPSIS
installboot bootblk raw-disk-device The boot(1M) program, ufsboot, is loaded from disk by the bootblock program which resides in the boot area of a disk partition. The ufs boot objects are platform-dependent, and reside in the /usr/platform/platform-name/lib/fs/ufs directory. The platform name can be found using the -i option of uname(1). The installboot utility is a SPARC only program. It is not supported on the architecture. users should use installgrub(1M) instead. bootblk The name of the bootblock code. raw-disk-device The name of the disk device onto which the bootblock code is to be installed; it must be a character device which is read- able and writable. Naming conventions for a SCSI or IPI drive are c?t?d?s? and c?d?s? for an IDE drive. Example 1: Installing UFS Boot Block To install a ufs boot block on slice 0 of target 0 on controller 1 of the platform where the command is being run, use: example# installboot /usr/platform/`uname -i`/lib/fs/ufs/bootblk /dev/rdsk/c1t0d0s0 /usr/platform/platform-name/lib/fs/ufs directory where ufs boot objects reside. /platform/platform-name/ufsboot second level program to boot from a disk or CD See attributes(5) for descriptions of the following attributes: +-----------------------------+-----------------------------+ | ATTRIBUTE TYPE | ATTRIBUTE VALUE | +-----------------------------+-----------------------------+ |Availability |SUNWcsu | +-----------------------------+-----------------------------+ od(1), uname(1), boot(1M), init(1M), kadb(1M), kernel(1M), monitor(1M), reboot(1M), rpc.bootparamd(1M), init.d(4), attributes(5) WARNINGS
The installboot utility fails if the bootblk or openfirmware files do not exist or if the raw disk device is not a character device. 11 Apr 2005 installboot(1M)
All times are GMT -4. The time now is 03:56 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy