STEP 1
# Set variable
FILE=/tmp/mainfile
SEARCHFILE =/tmp/searchfile
# THIS IS THE MAIN FILE.
cat /tmp/mainfile
Interface Ethernet0/0 "outside", is up, line protocol is up
Hardware is i82546GB rev03, BW 100 Mbps
Full-Duplex(Full-duplex), 100 Mbps(100 Mbps)
MAC address... (6 Replies)
I need help.....I have number of data files and I need to read the contains of each file which is three lines by awk commands or script, and send each line within the data file to different new file . That means I will have three files as a result, the first file will contains the first lines for... (4 Replies)
I am using the while-loop to read a file.
The file has lines with null-terminated strings (words, actually.)
What I have by that reading - just a first word up to '\0'!
I need to have whole string up to 'new line' - (LF, 10#10, 16#A)
What I am doing wrong?
#make file 'grb' with... (6 Replies)
Hi,
i have file which contains data as below(Only sample shown, it may contain more data similar to the one shown here)
i need to read this file line by line and generate an output file like the one below
i.e based on N value the number of MSISDNs will vary, if N=1 then the following... (14 Replies)
I have one long line text with semicolon used as separator between values in that line. Now, I want to separate the line into multiple line right after every 29th field.
example input line:
... (2 Replies)
I have one long line text with semicolon used as separator between values in that line. Now, I want to separate the line into multiple line right after every 29th field.
example input line:
... (1 Reply)
Hello,
I need a program that read a file line by line and prints out lines 1, 2 & 3 after an empty line... An example of entries in the file would be:
SRVXPAPI001 ERRO JUN24 07:28:34 1775
REASON= 0000, PROCID= #E506 #1065: TPCIPPR, INDEX= 003F
... (8 Replies)
Hi all,
I have a log file say Test.log that gets updated continuously and it has data in pipe separated format. A sample log file would look like:
<date1>|<data1>|<url1>|<result1>
<date2>|<data2>|<url2>|<result2>
<date3>|<data3>|<url3>|<result3>
<date4>|<data4>|<url4>|<result4>
What I... (3 Replies)
VP(4) Kernel Interfaces Manual VP(4)NAME
vp - Versatec printer-plotter
DESCRIPTION
Vp0 is the interface to a Versatec D1200A printer-plotter with a Versatec C-PDP11(DMA) controller. Ordinarily bytes written on it are
interpreted as ASCII characters and printed. As a printer, it writes 64 lines of 132 characters each on 11 by 8.5 inch paper. Only some
of the ASCII control characters are interpreted.
NL performs the usual new-line function, i.e. spaces up the paper and resets to the left margin. It is ignored however following a CR
which ends a non-empty line.
CR is ignored if the current line is empty but is otherwise like NL.
FF resets to the left margin and then to the top of the next page.
EOT resets to the left margin, advances 8 inches, and then performs a FF.
The ioctl(2) system call may be used to change the mode of the device. Only the first word of the 3-word argument structure is used. The
bits mean:
0400 Enter simultaneous print/plot mode.
0200 Enter plot mode.
0100 Enter print mode (default on open).
040 Send remote terminate.
020 Send remote form-feed.
010 Send remote EOT.
04 Send remote clear.
02 Send remote reset.
On open a reset, clear, and form-feed are performed automatically. Notice that the mode bits are not encoded, so that it is required that
exactly one be set.
In plot mode each byte is interpreted as 8 bits of which the high-order is plotted to the left; a `1' leaves a visible dot. A full line of
dots is produced by 264 bytes; lines are terminated only by count or by a remote terminate function. There are 200 dots per inch both ver-
tically and horizontally.
When simultaneous print-plot mode is entered exactly one line of characters, terminated by NL, CR, or the remote terminate function, should
be written. Then the device enters plot mode and at least 20 lines of plotting bytes should be sent. As the line of characters (which is
20 dots high) is printed, the plotting bytes overlay the characters. Notice that it is impossible to print characters on baselines that
differ by fewer than 20 dot-lines.
In print mode lines may be terminated either with an appropriate ASCII character or by using the remote terminate function.
FILES
/dev/vp0
SEE ALSO opr(1)VP(4)