I assume a hardware bug here.
Either the DVD drive is broken, or the memory bank (one of its DIMMs) that maps the I/O is broken.
Set diag-switch? to true and diag-level to max, and reset, then it should run a full memory test!
Thanks! Could you please tell me how to set. I tried
which didn't work.
Hello
I am trying to read from a small disk , 256 MB , removable sandisk.I am not able to access the device. The system does not recognise my disk to copy file s from the disk.
Please post your solution in this issue.
Thanks (2 Replies)
Hallo,
can You help me with this problem:
I have Hard Disk with "SCO Server Release 5.0" and I need read the data from the disk.
Know You how can I do it?
I only know that the file system is ISC UNIX .
I test FreeBSD, but I can not mount the disk (with error message "incorrect super block").... (7 Replies)
i was installing i my computer windows xp and sco
when i use knoppix5.0 live to read scsi partition wish sco was installing
show me message that i have not permission to acces in scsi hard drive
help me please (1 Reply)
Hi
I am using Solaris8.I want to find the total disk space of my server.Can anyone please tell that which field in below mentioned code signifies the disk space and whether this space is in Mb or GB.
c11t0d52 <EMC-SYMMETRIX-5264 cyl 4 alt 2 hd 15 sec 64>
... (4 Replies)
Being a novice user to linux i m little unaware of how would i check disk read write speed.
One of my mate is suggesting to create a file using dd command and check how much time it takes to create a 30 gb file .
I think this has a little sense however i would also like to take your reviews... (5 Replies)
Hi there,
I'm wondering how to display a disk label (why not edit it but I don't need that yet).
I found several commands on forums like disklabel and diskinfo but I can't find them on my system and don't know the package they belong to.
Can you help me?
Cheers
Santiago (2 Replies)
Would simply like to write data (no audio) to a CD/RW disk. The disk drive states CD/RW on the front but don't know for sure if the software is configured to recognize it as a writable disk. I can read/move data from the disk to the hard drive with no issue from the disk. Any help in this... (4 Replies)
i'm writing some code to simulate the boot progress after power on
but when i try to read the 2nd sector from a floppy disk, this operation always fail with ah=0x80h which means timeout, how can i get over this problem?
my code would be like this:
$ cat boot.S
.code16
#define SETUPLEN 4... (0 Replies)
Hello,
I need to get the lv mountpoint from the hdisk directly (from vgda i guess) and not from odm or /etc/filesystems
I knew the command, but unfortunately I forgot it ;)
cheers funksen (5 Replies)
Discussion started by: funksen
5 Replies
LEARN ABOUT DEBIAN
eepro100-diag
EEPRO100-DIAG(8) System Manager's Manual EEPRO100-DIAG(8)NAME
eepro100-diag - EEPROM setup and diagnostic program for Intel EtherExpress Pro100B, and EEPro PCI 10+ ethernet cards.
SYNOPSIS
eepro100-diag [options]
DESCRIPTION
eepro100-diag is a program that you can use to diagnose problems with ethernet cards based the "Speedo3" chip series: the i82557, '558 and
'559. These chips are used on the EtherExpress Pro100B, and EEPro PCI 10+.
OPTIONS
These programs follow the usual GNU command line syntax, with long options starting with two dashes (`-'). A summary of options is
included below.
-h, --help
Show summary of options.
-V, --version
Show version of program.
-v, --verbose
Verbose mode.
-q, --quiet
Be very unverbose.
-# <cardnum>, --card_num <cardnum>
Use card number <cardnum>.
-a, --show_all_registers
Print all registers.
-e, --show-eeprom
Dump EEPROM contents to stdout.
-E, --emergency-rewrite
Re-write a corrupted EEPROM.
-p, --port-base <port>
Specify port to use.
-A, --Advertise <mediaype>
Advertise media type. Valid Options are: 10baseT, 100baseT4, 100baseTx, 100baseTx-FD, 100baseTx-HD, 10baseT-FD and 10baseHD.
-F, --new-interface <interface>
Interface number. Options that make sense are: 10baseT, 10base2, AUI, 100baseTx, 10baseT-FDX, 100baseTx-FDX, 100baseT4, 100baseFx,
100baseFx-FDX, MII and Autosense.
-H, --new-hwaddress <address>
Set card to a new hardware address.
-m, --show-mii
Dump MII management registers.
-R, --reset
Reset the transceiver.
-T, --test
Do register and SRAM test.
-w, --write-EEPROM <values>
Write to the EEPROMS with the specified values. Do not use this, if you do not know what you do!
-f, --force-detection
Try to identify the card, even if it is active.
-t, --chip-type <card>
Explicitly set the chip. To get all valid numbers, run eepro100-diag with the options '-t -1'.
SEE ALSO mii-diag(8)AUTHOR
eepro100-diag was written and is still maintained by Donald Becker <becker@scyld.com>. This manual page was written by Alain Schroeder
<alain@debian.org>, for the Debian GNU/Linux system (but may be used by others).
February 18, 2002 EEPRO100-DIAG(8)