Hello,
I am getting below error in fmadm output. This server is not in support, so can't reach them. Is it showing that motherboard is faulty and should be replaced ? It was rebooted a week back and then, there were no errors
Code:
# fmadm faulty
--------------- ------------------------------------ -------------- ---------
TIME EVENT-ID MSG-ID SEVERITY
--------------- ------------------------------------ -------------- ---------
Sep 12 14:32:18 c5dade69-c238-6c70-9e67-802139045ff6 PCIEX-8000-3S Critical
Fault class : fault.io.pciex.device-interr max 40%
fault.io.pciex.bus-linkerr 20%
Affects : dev:////pci@400/pci@0/pci@8/scsi@0
dev:////pci@400/pci@0/pci@8
degraded but still in service
FRU : "MB" (hc://:product-id=SUNW,Netra-T5440:chassis-id=0920FM6015:server-id=v911j-zonemgr1-prod:serial=1563MLP-0816TA0183:part=541252905/motherboard=0)
faulty
Description : A problem has been detected on one of the specified devices or on
one of the specified connecting buses.
Refer to http://sun.com/msg/PCIEX-8000-3S for more information.
Response : One or more device instances may be disabled
Impact : Loss of services provided by the device instances associated with
this fault
Action : If a plug-in card is involved check for badly-seated cards or
bent pins. Otherwise schedule a repair procedure to replace the
affected device(s). Use fmdump -v -u <EVENT_ID> to identify the
devices or contact Sun for support.
--------------- ------------------------------------ -------------- ---------
TIME EVENT-ID MSG-ID SEVERITY
--------------- ------------------------------------ -------------- ---------
Sep 12 14:32:17 ea995552-75cf-e63d-be46-f4f445346028 SUNOS-8000-1L Minor
Fault class : defect.sunos.eft.undiagnosable_problem
Description : The EFT Diagnosis Engine encountered telemetry for which it is
unable to produce a diagnosis. Refer to
http://sun.com/msg/SUNOS-8000-1L for more information.
Response : Error reports from the component will be logged for examination
by Sun.
Impact : Automated diagnosis and response for these events will not occur.
Action : Run pkgchk -n SUNWfmd to ensure that fault management software is
installed properly. Contact Sun for support.
# pkgchk -n SUNWfmd
# fmstat
module ev_recv ev_acpt wait svc_t %w %b open solve memsz bufsz
cpumem-diagnosis 0 0 0.0 0.2 0 0 0 0 3.0K 0
cpumem-retire 2 0 0.0 1.2 0 0 0 0 20b 0
disk-transport 0 0 0.0 54.0 0 0 0 0 40b 0
eft 2 0 0.0 0.8 0 0 1 0 1.1M 0
etm 4 0 0.0 0.6 0 0 0 0 8.1K 0
fabric-xlate 0 0 0.0 0.0 0 0 0 0 0 0
fmd-self-diagnosis 2 2 0.0 0.1 0 0 1 0 22b 0
io-retire 2 0 0.0 0.6 0 0 0 0 0 0
snmp-trapgen 2 0 0.0 1.8 0 0 0 0 32b 0
sp-monitor 0 0 0.0 51.1 0 0 0 0 24b 0
sysevent-transport 0 0 0.0 122.8 0 0 0 0 0 0
syslog-msgs 2 0 0.0 0.9 0 0 0 0 0 0
zfs-diagnosis 345 278 0.0 30.7 0 0 0 0 0 0
zfs-retire 4 0 0.0 0.6 0 0 0 0 0 0
#
I have two files:
file1:
somedata
<html>
<head>
This is sample statement
......
......
</head>
</html>
somedata
file2:
olga 81 91 B A
rene 82 92 B A
zack 83 93
Expextd Result: (2 Replies)
Hi,
I am working on a command that replaces some occurrences of quotation marks in file. The quotation mark cannot be the first or the last character in line and cannot be preceded or followed by a comma.
I am not an expert in regular expressions, but I managed to create the following... (2 Replies)
Hi
Can anyone provide me the replacement of sed with xargs perl syntax for the below
sed -e :a -e '/;$/!N;s/\n//; ta' -e 's/;$//'
This should be without looping has to take minimal time for search (0 Replies)
I've been tasked with converting our software from strictly an IPv4 environment to handling both IPv4 and IPv6. I'm very nearly done and everything seems to be progressing just fine. There's just one thing that's been nagging me for a while now, so I thought I'd enquire about this.
I've read... (1 Reply)
There is a requirement that i need to replaced a pattern by another pattern in all the files in my entire file system. there are 1000s of file in the system. let the pattern is "calcuta". i have to replace this pattern by "kolkata" in all those files which contain "calcuta".
I am only able to... (12 Replies)
Hi All,
I have below file which has data in below format.
#$ | AB_100
| AB_300
()| AB_4
@*(% | AB-789
i want o/p as below format.
| AB_100
| AB_300
| AB_4
| AB-789
So here there is no standard format.
How we can achieve the same in unix ?
Regards, (3 Replies)
Hi,
i have a file with lines,
file.txt
-------
test is fun
testing is better
I need to replace 'test' to 'develop' and i used,
a=test
b=develop
sed "s,$a,$b,g" -------- but i see the word 'testing' is also replaced. Need some solution. Is there any way i could replace only 'test' ? (4 Replies)
Hi
pls help me for below;
i have a file .content is :
===================
uid,pcsPricingPlan,refPcsQosProfName
821910002022,smartlimit,SGSNQOS1
i have to replace the value of uid and pricingplan by a unix script.
may be the value would be next line or any where in the file.
pls... (9 Replies)
I recently picked up an HP9000 server running HPUX. I would like to replace the CRT terminal console with something I can use a flat panel monitor. Any suggestions would be greatly appreciated. (1 Reply)