06-13-2018
No, I couldn't find the firmware and HP wouldn't release any old firmware they may have in their archives, so I ended up tossing the Web Consoles, and have eventually decommissioned (finally) the old servers and replaced with IA64's . The few PA-RISC servers without the built-in Remote Consoles, that we have, now are attached to Serial Port Concentrators.
I guess, thanks for the concern.
8 More Discussions You Might Find Interesting
1. Shell Programming and Scripting
Hi all,
I am trying to eject the cdrom from a livecd after certain stage...
Now assuming that it is possible to eject,please consider my issue!!!
The OS boots into a regular user by default...so i am unable to use the eject command to push out the drive...
However if i try pfexec eject it... (3 Replies)
Discussion started by: wrapster
3 Replies
2. UNIX for Dummies Questions & Answers
Thanks
AVKlinux (3 Replies)
Discussion started by: avklinux
3 Replies
3. Shell Programming and Scripting
Hi All
I have written one shell script for GPRS route add is given below named GPRSRouteSet.sh
URL="www.google.com"
VBURL="10.5.2.211"
echo "Setting route for $URL for GPRS"
URL_Address=`nslookup $URL|grep Address:|grep -v "#"|awk -F " " '{print $2}'|head -1`
echo "Executing ... (3 Replies)
Discussion started by: mnmonu
3 Replies
4. UNIX for Advanced & Expert Users
Besides doing some shell-script which loops through /etc/passwd, I was wondering if there was some command that would tell me, like an enhanced version of getent.
The Operating system is Solaris 10 (recent-ish revision) using Sun DS for LDAP. (5 Replies)
Discussion started by: ckmehta
5 Replies
5. Shell Programming and Scripting
Hi I need help..........
I have an Sun One Directory server LDIF file with 5000 user entries, I need to change the data to match Test ID's, so I can run a perf test.
I'm way out of my league as I have not done any scripting for 10 years.
There are four entries for each user in the file... (3 Replies)
Discussion started by: Macdaddy99
3 Replies
6. Shell Programming and Scripting
i have a script which takes input from user, if user gives either Y/y then it should continue, else it should quit by displaying user cancelled.
#!/bin/sh
echo " Enter your choice to continue y/Y OR n/N to quit "
read A
if
then
echo " user requested to continue "
##some commands... (7 Replies)
Discussion started by: only4satish
7 Replies
7. UNIX for Dummies Questions & Answers
Whenever i switch from root to another user, by doing su - user, it takes me to home directory of user. This is very annoying as i want to be in same dir to run different commands as root sometimes and sometimes as normal user.
How to fix this? (1 Reply)
Discussion started by: syncmaster
1 Replies
8. Shell Programming and Scripting
Hi,
I need to switch from local user to root user in a shell script.
I need to make it automated so that it doesn't prompt for the root password.
I heard the su command will do that work but it prompt for the password.
and also can someone tell me whether su command spawns a new shell or... (1 Reply)
Discussion started by: Little
1 Replies
LEARN ABOUT OSF1
sys_attrs_bparm
sys_attrs_bparm(5) File Formats Manual sys_attrs_bparm(5)
NAME
sys_attrs_bparm - bparm subsystem attributes
DESCRIPTION
This reference page lists and describes attributes for the Boot Parameters (bparm) kernel subsystem. Refer to the sys_attrs(5) reference
page for an introduction to the topic of kernel subsystem attributes.
Identifies the device from which the system was last booted. This attribute corresponds to the console firmware environment vari-
able with the same name. Do not modify this value, which is set when the system boots.
A combination of flags that controls the boot loader and kernel. This attribute corresponds to the console firmware environment
variable with the same name. Values for the variable are: Boot to multiuser mode. By default, the kernel boots to single-user mode.
Enable the kdebug debugger to debug the kernel. By default, kdebug is not enabled in the kernel. Produce full dumps when the system
crashes. By default, partial dumps are produced. Prompt for an alternate kernel and special arguments when the system is booted. By
default, no questions are asked.
Set boot_osflags only at the console prompt or by using the consvar utility.
Identifies the boot device to be used when one is not included in the boot command line. This attribute corresponds to the console
firmware environment variable with the same name. Set bootdef_dev only at the console prompt or by using the consvar utility.
SEE ALSO
Commands: consvar(8)
Others: sys_attrs(5)
System Administration
sys_attrs_bparm(5)