J3591A, HP Secure Web Console firmware Post: 303018662

Sponsored Content

Operating Systems HP-UX J3591A, HP Secure Web Console firmware Post 303018662 by 0ddentity on Tuesday 12th of June 2018 06:14:55 PM

06-12-2018

Registered User

J3591A, HP Secure Web Console firmware

Hello all,

Looking for a pre v2.0 rev of firmware for this ancient device.

Nothing I've seen in searches indicates previous versions were available for download but I have to believe they were.

I've tried the new hpe community website, (formerly ITRC I believe) but no dice.

Also if anyone is using it still, is there a more modern way to access it other than via an old browser, or any modern network->serial port alternatives?

Many thanks,

-0

0ddentity

View Public Profile for 0ddentity

Find all posts by 0ddentity

2 More Discussions You Might Find Interesting

1. HP-UX

Secure Web Console Firmware

I have firmware 2.0 for the HP Secure Web Console, but looking for 1.8. Hp does not have this posted anywhere. Anyone have it? Thanks.

2. Solaris

Java web console Vs Web-Based Enterprise Management(WBEM)

Java web console Vs Web-Based Enterprise Management(WBEM) 1. I like to understand the difference in purpose of using java web console and Web-Based Enterprise Management (WBEM) 2. As per CIS benchmark, both of them has to be disabled when not used for increased security. Solaris admin(s) -...

LEARN ABOUT OSF1

malo

MALO(4) 						   BSD Kernel Interfaces Manual 						   MALO(4)

NAME

     malo -- Marvell Libertas IEEE 802.11b/g wireless network driver

SYNOPSIS

     To compile this driver into the kernel, place the following lines in your kernel configuration file:

	   device malo
	   device pci
	   device wlan
	   device firmware

     Alternatively, to load the driver as a module at boot time, place the following lines in loader.conf(5):

	   if_malo_load="YES"

DESCRIPTION

     The malo driver provides support for Marvell Libertas 88W8335 based PCI and Cardbus network adapters.  malo supports station and monitor mode
     operation.  Only one virtual interface may be configured at any time.  For more information on configuring this device, see ifconfig(8).

     This driver requires the malofw firmware kernel module be installed before it will work.  The firmware files are not publicly available.  A
     port of the firmware can be found at:

	   http://weongyo.org/project/malo/malo-firmware-1.4.tar.gz

     The firmware kernel module can be installed by extracting the archive and running 'make install clean' in the malo-firmware-1.4 directory.

HARDWARE

     The following cards are among those supported by the malo driver:

	   Card 		  Chip	     Bus	Standard
	   Netgear WG311v3	  88W8335    PCI	b/g
	   Tenda TWL542P	  88W8335    PCI	b/g
	   U-Khan UW-2054i	  88W8335    PCI	b/g

EXAMPLES

     Join an existing BSS network (i.e., connect to an access point):

	   ifconfig wlan create wlandev malo0 inet 192.168.0.20 
	       netmask 0xffffff00

     Join a specific BSS network with network name ``my_net'':

	   ifconfig wlan create wlandev malo0 ssid my_net up

     Join a specific BSS network with 64-bit WEP encryption:

	   ifconfig wlan create wlandev malo0 ssid my_net 
		   wepmode on wepkey 0x1234567890 weptxkey 1 up

SEE ALSO

     cardbus(4), pci(4), wlan(4), wlan_ccmp(4), wlan_tkip(4), wlan_wep(4), ifconfig(8), wpa_supplicant(8)

HISTORY

     The malo device driver first appeared in FreeBSD 7.1.

BSD
								 October 21, 2009							       BSD