I see hard and transport errors on all disks under treso pool and looks like some data corruption too. I want to take backup before, I reboot and replace disk. As of now, there are no slots free on server, so one option is, to break mirror, remove second disk (I need two disks, because data is 400GB). I have two spare disks, will insert in those slots, mount and copy data.
Can somebody help me to understand, if below setup shows me that I can detach disks without disturbing data and mount ?
Thanks
I tried rebooting my Sun server just a few minutes ago and I got the following at boot:
--
Sun Fire 280R (UltraSPARC-III+) , No Keyboard
Copyright 1998-2002 Sun Microsystems, Inc. All rights reserved.
OpenBoot 4.5, 1024 MB memory installed, Serial #xxxxxxxxx
Ethernet address... (6 Replies)
Actually have a few different issues, wondering if I could get input on (tried reading/searching for an answer, with no luck)
1. Have a v240 running sol9 that needs a bad disk replaced. So, here are the steps I took:
a. detached from mirroring
b. cleared mirroring (metaclear)
c.... (4 Replies)
All,
Here is the situation. Four 72GB hard drive installed on Sun V-240 server. HDD3 has gone bad. The server will not boot up completely. It keeps booting into single user mode. FSCK has been run and it did not fix the problem. I believe the harddrive is bad and needs to be replaced.
The... (1 Reply)
I have had a little issue with one of my disks, the usb cacble was pulled out and one of the external drives on it would no longer mount. I used First Aid and it verified and repaired both OK / nothing to do). After lots of messing around and not being able to mount I used Drive Genius 2 and that... (1 Reply)
Hello,
I'm brand new to Sun/Solaris.
I have a Sun Blade 150, with SunOS 5.8.
I wanted to make a backup to prevent future data loss, so I put the disk in a normal PC with Windows XP to try to make a backup with Norton Ghost, the disk was detected, but not the file volume, so I place the disk... (6 Replies)
Originally Posted by panos83
Hello there Sir,
according to this old post,
https://www.unix.com/sco/100001-warni...ler-found.html
i try to restore an old image to a new hard disk drive.
The problem is that i don't have basic information such as:
1) Which btld driver do i... (3 Replies)
Scenario1:
VG00 lvm,not mirrored,2 disk of 36GB vg size
VG00 size is under 30G.
Is possible to remove a disk of 36GB and replace "on fly"
with a disk of 300GB on VG00?
Thanks (6 Replies)
This is first time post...found this forum when looking for possible solution to fix my sun pc. Just one day can't boot it already showing the following:
Boot device: disk File args:
Bad magic number in disk label
Can't open disk label package
Evaluating: boot
Can't open boot device... (40 Replies)
Hi Guys,
I have fresh new installed VIO 2.2.3.70 on a p710, 3 physical SAS disks, rootvg on hdisk0
and 3 VIO clients through vscsi, AIX7.1tl4 AIX6.1tl9 RHEL6.5ppc, each lpar has its rootvg installed on a LV on datavg (hdisk2) mapped to vhost0,1,2
There is no vg on hdisk1, I use it for my... (1 Reply)
Discussion started by: frenchy59
1 Replies
LEARN ABOUT ULTRIX
reboot
reboot(8) System Manager's Manual reboot(8)Name
reboot - automatic reboot procedures
Syntax
/etc/reboot [ -n ] [ -q ]
Description
The ULTRIX system is booted by loading a kernel image, usually into memory at location zero and transferring to zero. Because the system
is not reenterable, the kernel image must be read in from disk each time the system is bootstrapped.
When the reboot of a running system is desired, is normally used. If there are no users, can be used. The command causes the disks to be
synced, and then a multiuser reboot is initiated. The system is booted and an automatic disk check is performed. If the procedure suc-
ceeds, the system is then brought up for the users.
The system will reboot itself after a power failure or after a crash, provided auto-restart is enabled on your system. A consistency check
of the file systems will be performed and, unless the check fails, the system will resume multiuser operations.
Options-n Prevents the disks from being synced.
-q Reboots quickly and ungracefully, without shutting down running processes first.
Files
System code
See Alsocrash(8v), fsck(8), halt(8), init(8), newfs(8), rc(8), shutdown(8)reboot(8)