Sponsored Content
Operating Systems AIX PowerVM SEA etherchannel performance ? Post 303018531 by vilius on Saturday 9th of June 2018 08:42:55 AM
Old 06-09-2018
largesend=1 is default on my vios version - tried large_receive=yes - no change same result 1.4-1.8Gbit speed.
 

10 More Discussions You Might Find Interesting

1. AIX

Problem with Etherchannel

I'm trying to configure Etherchannel on AIX 5.3 and I'm having some problems. I am aggregating both of the onboard NIC's (ent0 and ent1) into a new adapter ent2 for failover reasons obviously. At first I was experiencing a problem where about 50% of all my packets would be dropped. Then after... (4 Replies)
Discussion started by: acascianelli
4 Replies

2. AIX

AIX / Etherchannel / VLANs

I have 1 AIX server, 4 dual ported fiber attached ethernet cards and 4 VLANS coming in. Is it possible to present those 8 ports as 1 IP address using etherchannel? Thanks. (5 Replies)
Discussion started by: jwholey
5 Replies

3. AIX

Can EtherChannel be a redundancy config?

I have one p5 server, no lpar, 2 physical network adapter, bundle as one EtherChannel. The two 2 physical network adapter connect to 2 network switches. How to make this as a redundancy config? Current is if one physical network adapter down, the seond one will go through the network. but if... (2 Replies)
Discussion started by: rainbow_bean
2 Replies

4. AIX

EtherChannel interface ping pelicularity

I have few AIX servers in my data center, which have their EtherChannel configured to have a fat pipe (active/active) and a nagios server to monitor the server uptimes. Nagios server pings every server in the data center and we have pretty much every known unix flavor in this data center. When... (3 Replies)
Discussion started by: thenomad
3 Replies

5. AIX

Aggregated Etherchannel

Hi, I have a AIX5.3 P6-520 with 8x1Gb Ethernet ports with possible connections to 2 CISCO 2960 switches. I can create 8023ad Etherchannels which work correctly with the switches (I have set up for LACP passive and a valid channels) But can create 2x 8023ad 4Gb Etherchannels with no backups.... (2 Replies)
Discussion started by: spitzie
2 Replies

6. AIX

PowerVM HA questions

hi guys, i need to develop following setup for a customer: high availability oracle database on aix7 and linux in 2 different LPAR using dual ps700 blande a ds3400 and HMC. the question is, it is possible to have automatic vioc failover(aix,linux) when for example 1 vios goes down? in... (6 Replies)
Discussion started by: gullio23
6 Replies

7. AIX

Need IBM PowerVM

Hi all please give me a link for IBM PowerVM (4 Replies)
Discussion started by: babinlonston
4 Replies

8. AIX

Etherchannel failover testing

Hi Guys, I am trying to test an etherchannel failover and switchback. I did failover from primary to backup adapter, but now I am not able to switch it back to primary. phcxxxxx:/ > entstat -d ent4 | grep Active Active channel: backup adapter ... (1 Reply)
Discussion started by: snchaudhari2
1 Replies

9. AIX

PowerVM/lpar creation problems

Hi, I'm a newbie to PowerVM and LPARs ( I work with VmWare and Oracle VM Server for Sparc) .recently we purchased an 8202-e4b server, with two enclosures for add'l disk capacity. it is licensed for PowerVM standard,came preloaded as such, AIX 7.1. I've set up HMC v8.2, and run it through a VM on... (30 Replies)
Discussion started by: computron
30 Replies

10. AIX

Powervm ivm vios

Hello, After installing on P6 which is POWERVM IVM VIOS enabled (VET CODE D21C77ACD9229817CA1F00002C10004164 ) i get this message "I/O hosting requires a hosting partition - boot not permitted". HMC was connected to the machine then HMC was removed through ASMI Searching on... (2 Replies)
Discussion started by: filosophizer
2 Replies
i8kctl(1)							     Utilities								 i8kctl(1)

NAME
I8kctl, i8kfan - Utility to access SMM BIOS on Dell Inspiron laptops SYNTAX
i8kctl [<command> [<args>]] i8kfan [<left> [<right>]] DESCRIPTION
The i8kctl utility provides a command-line interface to the i8k kernel driver for Dell Inspiron laptops. When invoked without arguments the program reports the same information which can be read from the /proc/i8k file: 1. i8k format version 2. bios version 3. machine id 4. cpu temperature 5. left fan status 6. right fan status 7. left fan speed 8. right fan speed 9. ac power status 10. fn buttons status The optional command argument can be used to select only one of the above items. Command can be: version, bios, id, temp, fan, speed, ac and fn. Examples: $ i8kctl 1.0 A17 B5W123K 52 2 1 8040 6420 1 2 $ i8kctl temp 52 $ i8kctl fan 2 1 The fan command can accept two optional parameters which specify the new fan state for left and right fans. The state parameter can be: 0 turn the fan off 1 set low speed 2 set high speed - don't change the state of this fan For example the command: $ i8kctl fan - 2 sets the right fan to high speed and leaves the left unchanged. It should be noted that if the i8kmon(1) daemon is used to control the fans, setting the speed with i8kfan is pointless since the daemon will override the speed with its own value. Invoking i8kctl as i8kfan is the same as invoking the program with the fan option: $ i8kctl fan 1 2 1 2 $ i8kfan 1 2 1 2 FILES
/proc/i8k AUTHORS
Massimo Dal Zotto <dz@debian.org> COPYRIGHT
i8kctl and all the i8kutils programs , scripts and other files are distributed under the GNU General Public License (GPL). On Debian GNU/Linux systems, the complete text of the GNU General Public License can be found in `/usr/share/common-licenses/GPL'. SEE ALSO
i8kmon(1), i8kbuttons(1) Massimo Dal Zotto 18 March 2002 i8kctl(1)
All times are GMT -4. The time now is 05:55 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy