Sponsored Content
Operating Systems Linux Add two different subnet public IPs to single NIC or two different NIC on same box Post 303018439 by rbatte1 on Wednesday 6th of June 2018 09:55:48 AM
Old 06-06-2018
Can you explain what NICs you have, what is currently configured (i.e. the output from ip a s) and what you want to add and your attempts so far. There are various options to consider, so it woud be useful to understand your needs before just setting off, otherwise this is all a bit vague.


I'm sure we can help you through.


Kind regards,
Robin
 

9 More Discussions You Might Find Interesting

1. IP Networking

How to put 2 IPs on a single NIC

Hi ! I've just got a real IP number for my personal computer. Until now, the IP was masked (NAT'ed). Anyway, the problem is like this : I'm on a LAN with about 100 computers and I asked the admin to give me a real IP so that I can connect to my computer from my office. He gived that IP to me, but... (1 Reply)
Discussion started by: Sergiu-IT
1 Replies

2. Solaris

Sun box's NIC speed setting

Is there a way to check if my Sun box's network interface card is set to 10 or 100 Mbps? Thanks! (1 Reply)
Discussion started by: FredSmith
1 Replies

3. HP-UX

how can I determine which NIC card is virtual NIC Card

how can I determine which NIC card is virtual NIC Card which condition can make a decision Does HP UX have Virtual Network Adapter Concept if ,it has where I can Find if I Install Virutal Network Adapter or which command that i can get it or which software can generate thanks (2 Replies)
Discussion started by: alert0919
2 Replies

4. Solaris

x86 Solaris 10 nic driver added but not attached. NIC is not detected.

I couldn't install my nic in solaris 10. I compiled and added the driver but failed to attach the driver and ifconfig output shows only loopback dev. Please see the following output and tell me whether my nic has been detected and why the driver failed to attach? My nic is detected in linux... (0 Replies)
Discussion started by: vectrum
0 Replies

5. IP Networking

squid proxy: one NIC for inbound & one NIC for outbound?

I am new in squid proxy. My question is how to (and if it's necessary) to set one NIC for inbound traffic (http requests) and one NIC for outbound traffic (http answers)? Thank you in advance! (4 Replies)
Discussion started by: aixlover
4 Replies

6. Red Hat

I want to tune NIC's rps, rfs and xps value. which NIC device should I modify.

Dear All I want tune my NIC's rps, rfs and xps value. In my system I have two NIC (eth0, eth1) and I have a bond0 ( eth0, eth1). Here is the question? Which device should I modify ? eth0 and eth1? or just modify bond0 or modify all device (eth0, eth1, bond0) Any advice is welcome.... (0 Replies)
Discussion started by: nnnnnnine
0 Replies

7. Solaris

Solaris 11 2nd nic for different subnet

I have a Solaris 11 machine with 2 network cables attached. The first one is the default route and is working okay. I am trying to activate the second on another subnet, but am sure missing something. The first one is on 10.30.128. and with it everything works fine, but when I try to add the... (0 Replies)
Discussion started by: ad101
0 Replies

8. Solaris

Solaris 2nd nic for different subnet

posted this on the other sub-forum https://www.unix.com/unix-for-dummies-questions-and-answers/246504-solaris-11-2nd-nic-different-subnet.html apologies if linking is not appropriate Thanks for your help. (0 Replies)
Discussion started by: ad101
0 Replies

9. UNIX for Advanced & Expert Users

Changing single path NIC to a teamed connection in same subnet

Dear all, I have a remote CentOS7 server that has two network cards. Each card has four ports and port one of card one was defined with the IP address assigned to the server. So far, so good and it's been working for over a year. We have now got cables sorted out so there are four paths... (4 Replies)
Discussion started by: rbatte1
4 Replies
diction(1)						      General Commands Manual							diction(1)

NAME
diction, explain, suggest - Prints wordy sentences and looks them up in an interactive thesaurus. SYNOPSIS
diction [-fpattern_file] [-k] [-ma] [-me] [-ml] [-ms] [-n] [file...] explain suggest The diction command finds all sentences in an English language document that contain phrases from a database of bad or wordy diction. The explain command is an interactive thesaurus for the English language phrases found by the diction command and only for those phrases. The diction command reads from standard in if no file operand is provided. The suggest command is a synonym for explain. OPTIONS
Names a user-created pattern file to be used in addition to the default file. Passes the -k option to the deroff command. The -k option keeps blocks of text specified nroff by requests or macros; for example, the request. Passes the -ma option to deroff. The -ma option interprets nroff man macros only. Overrides the default nroff -ms macro package. Causes deroff to skip lists; should be used if a docu- ment contains many lists of nonsentences. Overrides the default nroff -ms macro package. Suppresses use of the default file (used with -f). Only the user-created pattern file is used. DESCRIPTION
Each phrase found by the diction command is enclosed in [ ] (brackets). Because diction runs deroff before looking at the text, include formatting header files as part of the input. Before using the explain command, use the diction command to obtain a list of poorly worded phrases. When you use the explain command, the system prompts you for a phrase and responds with a grammatically acceptable alternative. You can continue typing phrases, or you can exit by pressing the End-of-File key sequence. The explain command can also take input redirected from a file. No other command line arguments are valid. NOTES
Use of nonstandard formatting macros may cause incorrect sentence breaks. In particular, diction does not understand -me. FILES
Default pattern file. Thesaurus used by the explain command. SEE ALSO
Commands: deroff(1), nroff(1) diction(1)
All times are GMT -4. The time now is 04:54 PM.
Unix & Linux Forums Content Copyright 1993-2022. All Rights Reserved.
Privacy Policy