Not working:-
in AIX , if we type "nfso -a"
we see some parameters, in which there is one which states that
however keeping "0" value here does resolve the NAS issue of mounting but it is not safe as per SCD to allow NAS coomunication to happen between aix client and storage on random ports.
but when we keep 1 we face the issue as it only takes 1021 1022 1023 ports as source port for mounting.
so my question is , can we specified that only 3000 to 3020 ports be used for NAS mount points?
Hi Guys,
i am trying to open a port in AIX.
but i am not able to get the command for this. AIX is not having the iptables file present.
So please any body can tell me how to open a port in AIX...
Thanks
sanju (2 Replies)
Hi,
I am working with sun Solaris 5.9 and in my application,I have to communicate with Serial port(i.e /dev/term/a).
So I need source code to by which I can do the following things--
1)check the port is available or not.If it dosn't find the port,it should throw the error message(i.e. port not... (0 Replies)
In general for intalling a package like we do
./configure, make , make install
But if we want to integrate the package with a huge source base
what are the things to be taken care
could some one have a light on purpose of ./configure , make and make install
along with above question.
I... (1 Reply)
Hi,
I was looking on Google for AIX-VIO/LPAR with ISCSI solution and found following really nice tutorial about how to setup ISCSI with free NAS.
1) Build Your Own Open Source NAS Device Using FreeNAS | Train Signal Training - Free Computer Training Videos
2) Build Your Own Open Source... (4 Replies)
Hello all. I have never had any issues like this when compiling applications from source. When I try to compile samba-3.5.0pre2, configure runs with no issues, but when the time comes to make, this happens:
make: make 1254-025 There must be an existing description file or specify a target.
... (4 Replies)
Hello Gurus,
I was trying to find who's using my port and got below answer from a IBM website. But the problem with the below answer is I need a root to run the rmsock, is there any other alternative to find out who is using my port with out a root access??
1. netstat -Aan | grep <port... (1 Reply)
Hi all,
I need to change the source port number of an outgoing TCP packet. First I have to bind the socket to a particular port(suppose 9001) but when I send the TCP packet I want to change the source port number lets say to 9002 still letting the socket to be bound to the same old port (9001).... (0 Replies)
Hello all,
I need your help with any command to release a port on AIX.
Thanks for all. (5 Replies)
Discussion started by: Mcipamo
5 Replies
LEARN ABOUT X11R4
systemd-volatile-root.service
SYSTEMD-VOLATILE-ROOT.SERVICE(8) systemd-volatile-root.service SYSTEMD-VOLATILE-ROOT.SERVICE(8)NAME
systemd-volatile-root.service, systemd-volatile-root - Make the root file system volatile
SYNOPSIS
systemd-volatile-root.service
/lib/systemd/systemd-volatile-root
DESCRIPTION
systemd-volatile-root.service is a service that replaces the root directory with a volatile memory file system ("tmpfs"), mounting the
original (non-volatile) /usr inside it read-only. This way, vendor data from /usr is available as usual, but all configuration data in
/etc, all state data in /var and all other resources stored directly under the root directory are reset on boot and lost at shutdown,
enabling fully stateless systems.
This service is only enabled if full volatile mode is selected, for example by specifying "systemd.volatile=yes" on the kernel command
line. This service runs only in the initial RAM disk ("initrd"), before the system transitions to the host's root directory. Note that this
service is not used if "systemd.volatile=state" is used, as in that mode the root directory is non-volatile.
SEE ALSO systemd(1), systemd-fstab-generator(8), kernel-command-line(7)systemd 237SYSTEMD-VOLATILE-ROOT.SERVICE(8)