bonding: bond0: link status definitely down for interface eth1, disabling it
tg3 0000:03:00.1: eth1: Link is up at 100 Mbps, full duplex
tg3 0000:03:00.1: eth1: Flow control is off for TX and off for RX
: tg3 0000:03:00.1: eth1: EEE is disabled
bond0: link status definitely up for interface eth1, 100 Mbps full duplex.
tg3 0000:03:00.1: eth1: Link is down
bonding: bond0: link status definitely down for interface eth1, disabling it
tg3 0000:03:00.1: eth1: Link is up at 100 Mbps, full duplex
tg3 0000:03:00.1: eth1: Flow control is off for TX and off for RX
tg3 0000:03:00.1: eth1: EEE is disabled
bond0: link status definitely up for interface eth1, 100 Mbps full duplex.
tg3 0000:03:00.1: eth1: Link is down
bonding: bond0: link status definitely down for interface eth1, disabling it
tg3 0000:03:00.1: eth1: Link is up at 100 Mbps, full duplex
tg3 0000:03:00.1: eth1: Flow control is off for TX and off for RX
tg3 0000:03:00.1: eth1: EEE is disabled
bond0: link status definitely up for interface eth1, 100 Mbps full duplex.
uname -r = 2.6.32-279.el6.x86_64
modinfo tg3 = 3.122
Why the eth1 always down every 5 minutes?
Regards
Marry Jane
Moderator's Comments:
Please use CODE tags as required by forum rules!
Last edited by RudiC; 05-16-2018 at 05:20 AM..
Reason: Added CODE tags.
Hi, folks.
Sorry for bothering, but maybe someone could help me please.
The problem is the following:
there is some script that copies files from local file system to AFS. The copying is performed with dd command.
The script copies data into some AFS volumes.
The problem appeared with one... (0 Replies)
Hi
Please help me with the following problem with my script.
The following block of code is not repeating in the while loop and exiting after searching for first message.
input_file
==========
host001-01
host001-02
2008-07-23 13:02:04,651 ConnectionFactory - Setting session state... (2 Replies)
Hi
I am right now facing a strange hardware problem. System get booted with the following error:
Fatal Error Reset
CPU 0000.0000.0000.0003 AFSR 0100.0000.0000.0000 SCE
AFAR 0000.07c6.0000.1000
SC Alert: Host System has Reset
It happen 4 or 5 times and get the same error every time.I... (8 Replies)
1) when user login to the server the session got colosed. How will resolve?
2) While firing the command ls -l we are not able to see the any files in the director. but over all view the file system using the command df -g it is showing 91% used. what will be the problem?
Thanks in advance. (1 Reply)
Hi,
i've a redhat linux 9 upadated by redhat from 7 version to 9 version. A couple of days ago i was a problem with my mail, in other words i'm not able to get any email nor to send any email. I've a proxy configuration and i tried to set iptables in order to verify the port. The 110,255 and 995... (1 Reply)
At work I am trying to get this one Linux machine (let's call it ctesgm07) to behave like another Linux machine that we have (let's call it test007).
test007 returns the following version info:
cat /etc/debian_version: lenny/sid
uname -a: Linux test007 2.6.27-7-generic #1 SMP Tue Nov 4... (0 Replies)
Hi,
This is rather a question from a "user" than from a sys admin, but I think this forum is apropriate for the question.
I have an adress with automatic email forwarding and for some senders (two hietherto), emails are bouncing. This has really created a lot of problems those two time so I... (0 Replies)
We recently had some HP DL380 G8 servers delivered and I have installed RHEL 5.6 and 5.8 on them. Both OS use the Tegon3 driver for the BCM 5719 onboard NICs.
Trouble I had was when any command expecting a lot of output ie sysctl -a was run the system hangs up and stops responding to ping for... (0 Replies)
I don't know if you guys get this problem sometimes at Terminal but I had been having this problem since yesterday :( Maybe I overdid the Terminal. Even the codes that used to work doesn't work anymore.
Here is what 's happening:
* I wanted to remove lines containing digits so I used this... (25 Replies)
Hi everyone,
I am experiencing discontinuity of Internet service, this started 1 month ago. Everything worked very well for 1 year of intensive use, but now, I have problems reaching my gateway.
The gateway is not my router but a node belonging to my ISP and I share the same public IP with... (3 Replies)
Discussion started by: remic
3 Replies
LEARN ABOUT SUSE
ifcfg-bonding
IFCFG-BONDING(5) Network configuration IFCFG-BONDING(5)NAME
ifcfg-bonding - interface bonding configuration
SYNOPSIS
/etc/sysconfig/network/ifcfg-bond*
Bonding Interfaces
To setup a bonding interface you need a configuration file ifcfg-bond<X> with the usual network settings. But you must add additional vari-
ables
BONDING_MASTER
must be set to 'yes' to identify this interface as a bonding interface
BONDING_SLAVE_<X>
here you specify the interface name representing the slave network interfaces.
BONDING_MODULE_OPTS
contains bonding options. Here you can set interface timeouts or working modes ('mode=active-backup' for backup mode). For addi-
tional information take a look into the documentation mentioned at the bottom. Note, that this options are not passed as parameters
to the bonding kernel module any more, but set via sysfs interface. This variable will be renamed in the feature.
BONDING_SKIP_REMOVE_WORKAROUND
When set to "yes", a bonding interface will be not removed while ifdown any more to avoid problems, e.g. when some third party ker-
nel module, such as Veritas 'llt' module, does not react correctly to the UNREGISTER event and does not remove its references to the
bonding interface causing all network related operation to stuck.
Note: the bonding options are not reverted when this option is enabled and it is required to either explicitly keep the old options
and set them to their default setting on bonding configuration changes or to reboot.
Example
Example for a bonding interface on eth0 and eth1 using the backup mode
ifcfg-bond0
STARTMODE='onboot'
BOOTPROTO='static'
IPADDR='192.168.0.1/24'
BONDING_MASTER='yes'
BONDING_SLAVE_0='eth0'
BONDING_SLAVE_1='eth1'
BONDING_MODULE_OPTS='mode=active-backup miimon=100'
Additional Information
For additional and more general information take a look into /usr/src/linux/Documentation/networking/bonding.txt. Maybe you need to
install the kernel sources to get this additional documentation.
The configuration of routes for this kind of interface does not differ from ordinary interfaces. See man routes for details.
BUGS
Please report bugs at <http://www.suse.de/feedback>
AUTHOR
Christian Zoz <zoz@suse.de> -- ifup script
Wilken Gottwalt <wgottwalt@suse.de> -- ifcfg-bonding manual page
SEE ALSO ifcfg(5), ifup(8).
sysconfig April 2005 IFCFG-BONDING(5)
05-16-2018
