05-15-2018
No there isn’t a /u file system I believe. All data is one folder named /dat. I believe some of the sco files are modified by the Activant application though, so that could be some of my issues.
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
rmf(1) General Commands Manual rmf(1)
NAME
rmf - remove folder (only available within the message handling system, mh)
SYNOPSIS
rmf [+folder] [-help] [-[no]interactive]
OPTIONS
Prints a list of the valid options to this command. Asks for confirmation before deleting a folder. By default, rmf deletes a folder and
its messages without asking for confirmation. If you specify the -interactive option, rmf asks if you are sure before deleting the folder.
You are advised to use this option, since when rmf deletes a folder its contents are lost irretrievably.
DESCRIPTION
The rmf command removes all of the messages within the current folder, and then removes the folder itself. If there are any files within
the folder which are not part of MH, they are not removed, and an error message is displayed.
You can specify a folder other than the current folder by using the +folder argument. If you do not specify a folder, and rmf cannot find
the current folder,rmf asks you whether you want to delete +inbox instead.
If the current folder is removed, it makes +inbox current.
Note that the rmf command irreversibly deletes messages that do not have other links, so use it with caution.
If the folder being removed is a sub-folder, the parent folder becomes the new current folder, and rmf tells you that this has happened.
This provides an easy mechanism for selecting a set of messages, operating on the list, then removing the list and returning to the current
folder from which the list was extracted.
Using rmf to delete a read-only folder deletes the private sequence and current message information from the file, without affecting the
folder itself. If you have sub-folders within a folder, you must delete all the sub-folders before you can delete the folder itself.
PROFILE COMPONENTS
Path: To determine the user's Mail directory
EXAMPLES
This example shows how rmf asks for confirmation when the -interactive option is used: % rmf -interactive +test Remove folder "test"? y
FILES
The user profile.
SEE ALSO
rmm(1)
rmf(1)