05-15-2018
i would only copy the data files, assuming that the application programs are the at the same release. is there a separate /u file system?
10 More Discussions You Might Find Interesting
1. UNIX for Dummies Questions & Answers
I've just installed Unix SCO OpenServer System v in an Intel PC and Everithing ok, except just one thing, in the begining of the installation the wizard asked me about the mouse , i have a generic 3 buttons mouse and i took a logitech and did not work
i need to change the mouse configuration, ... (2 Replies)
Discussion started by: jimmyvaldes
2 Replies
2. UNIX for Dummies Questions & Answers
hello!
when i try to make my system dual boot with both win98 & sco open server 5.5 it doesn't work at all.neither win98 take start nor sco open server boots.what should i do ?
kindly help me
thanks (1 Reply)
Discussion started by: buntty
1 Replies
3. IP Networking
I have certain problems while Installing UNIX OPENSERVER.Could anyone solve that if I provide that problem. (3 Replies)
Discussion started by: Rajraius
3 Replies
4. SCO
Hi everyone,
We r installing sco openserver 5.07 on dell poweredge 2800 but we are facing problem when installing SCSI-raid drivers. Dell provide Perc4 raid card and we dont found raid drivers for this specific raid card. So we r stuck up on primary stage and we also dont know the... (2 Replies)
Discussion started by: mineshkoli
2 Replies
5. SCO
we are installing Openserver 5.0.7, system have SAS controller (Hard Disk Attached) as well as Adaptec ultra 320 controller (Tape Drive Attached).
At the time of installation we link both driver BTLD
Boot: Defbootstr link=accraid ad320
Aftes succesfully installation of accraid btld... (6 Replies)
Discussion started by: hafizurr
6 Replies
6. SCO
I'm trying to install openserver 6.0 on a locally assembled ACPI Multiprocessor PC with an intel core 2 dou e4400 @ 2 ghx and a WD8000JD SATA HD. Immediately after the startup screen I get "PANIC: kernel-mode address fault on kernel address 0xf000ff53". I get this message even if the drive is... (1 Reply)
Discussion started by: tvmccorm
1 Replies
7. SCO
can not for the life of me workout which BTLD to load allways shows no HDD available can any one give me a clue
tried
hpsas
aacraid
lsil
a160
a320
server is a ML310 G4 ?????:confused::confused: (7 Replies)
Discussion started by: wildginger
7 Replies
8. SCO
hello, i want to install release 5.0.5 on my notebook but the system hangs when extracing files from source media in fact after configuration all of setting please help me:confused: (1 Reply)
Discussion started by: hossein
1 Replies
9. UNIX for Advanced & Expert Users
Hi All ,
I wanted to install SCO Open server 5.0.7 on HP DC7600 Desktop Machine, is there any bootloader and which site i can find it to enable me install it because the system is not recognizing the Hard disk just like the ML G Series machine installations.
Please help if you have done this... (4 Replies)
Discussion started by: davosky
4 Replies
10. UNIX for Advanced & Expert Users
Hi:
I'm installing SCO Open Server 6.0v on VMWare ESXi,
The instalation procedure giving by UnXis is using OVF deploy template and
it create a primary partition of 10gb only.
Any one know, if the OVF template could be edited to create a larger partition??
Thanks (0 Replies)
Discussion started by: Ccarballo
0 Replies
FSPLIT(1) General Commands Manual FSPLIT(1)
NAME
fsplit - split a multi-routine Fortran file into individual files
SYNOPSIS
fsplit [ -e efile] ... [ file ]
DESCRIPTION
Fsplit takes as input either a file or standard input containing Fortran source code. It attempts to split the input into separate routine
files of the form name.f, where name is the name of the program unit (e.g. function, subroutine, block data or program). The name for
unnamed block data subprograms has the form blkdtaNNN.f where NNN is three digits and a file of this name does not already exist. For
unnamed main programs the name has the form mainNNN.f. If there is an error in classifying a program unit, or if name.f already exists,
the program unit will be put in a file of the form zzzNNN.f where zzzNNN.f does not already exist.
Normally each subprogram unit is split into a separate file. When the -e option is used, only the specified subprogram units are split
into separate files. E.g.:
fsplit -e readit -e doit prog.f
will split readit and doit into separate files.
DIAGNOSTICS
If names specified via the -e option are not found, a diagnostic is written to standard error.
AUTHOR
Asa Romberger and Jerry Berkman
BUGS
Fsplit assumes the subprogram name is on the first noncomment line of the subprogram unit. Nonstandard source formats may confuse fsplit.
It is hard to use -e for unnamed main programs and block data subprograms since you must predict the created file name.
4.2 Berkeley Distribution April 29, 1985 FSPLIT(1)